Furuno FCV-38 Скачать руководство пользователя страница 19

Страница: 19 / 152

1. OPERATION

1-7

1.3.5

InstantAccess bar™ icons list

The table below shows the InstantAccess bar™ menus, their respective menu items
and available options, along with a brief description. For full details on each menu/
function, see the respective sections of the manual.

Icon

Description/Options

Menu

Item

[Sounder] menu.
Accesses the sounder-related settings.

[Interference Rejection] icon.
Accesses the [Interference Rejection] function. See section 1.10.

[Smoothing] icon.
Accesses the [Smoothing] function. See section 1.11.

[Clutter] icon.
Accesses the [Clutter] (low level noise reduction) function.
See section 1.12

[Zoom Mode] icon.
Accesses the [Zoom] functions. See section 1.13.

[Measure Fish Size] icon.
Accesses the fish measurement area settings. See section 2.2.2. The
available settings are:

[External Fish Finder Gain] icon.
Adjusts the external fish finder gain. See section 1.7. The available op-
tions are:

Note:

Available when the external fish finder window setting is “OFF”.

[Calibration Range] icon.
Activates/deactivates the calibration range display. See section 5.4.

Measures fish over the entire display.
See section 2.2.3.
Measures fish within a specified depth range.
See section 2.2.4.

Measures fish that appear near the seabed.
See section 2.2.5.

Measures fish within a specified area on the display.
See section 2.2.6.

Adjusts the high frequency external fish finder gain.

Adjusts the low frequency external fish finder gain.

Содержание FCV-38

























































































































































Результаты поиска

Содержание FCV-38

Отзывы:

Бренды по названию

Популярные бренды

Furuno FCV-38, Руководство пользователя

Результаты поиска

Содержание FCV-38

Отзывы:

Бренды по названию

Популярные бренды