manualshive.com logo in svg

Furuno FCV-38, Руководство пользователя

Поделиться
Скачать
Furuno FCV-38 Скачать руководство пользователя страница 79

3.  SCREENSHOTS & DATA RECORDING

3-7

3

2. If you need to filter the files, select the filter button, indicated in the figure on the 

previous page. The filter options window, shown below, appears. If you have no 
need to filter the files, go to step 4.

3. Referring to the table below, set the appropriate file filters, then click [OK].

Filter type

Description

[Specify Date]

Applies a filter based on date. You can select a single filter (for ex-
ample, filter by month only) or a mixed filter (for example, filter by 
year, month and date).

[Specify Position] Applies a filter based on a specific location and/or a nautical mile ra-

dius from the specified point.

[Sort Recordings] Applies a filter based on the playback time of the record, the depth 

recorded, or a mix of time and depth.
•  [Minimum Time]/[Minimum Depth]: Records with a time/depth be-

low this setting are not displayed.

•  [Maximum Time]/[Maximum Depth]: Records with a time/depth 

above this setting are not displayed.

Specify Date

Year

Month

Day

- - - -

- - - -

- - - -

N

0

0

0

E

0

0

0

50

1

2

40

80

Degree

Minute

Second

Degree

Minute

Second

Specify Position

Latitude

Longitude

Radius [nm]

Minimum Time

Maximum Time

Minimum Depth

Maximum Depth

Sort Recordings

OK

Cancel

Date filter 
options

Position filter 
options

Sort filter 
options

Содержание FCV-38

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды