Furuno FCV-38 Скачать руководство пользователя страница 21

Страница: 21 / 152

1. OPERATION

1-9

[Graph] menu.
Accesses the graph functions.
See chapter 2.

[Fish Size Graph].
Activates/deactivates the fish size graph and measurement functions.
See section 2.2.
[Target Graph] icon
Activates/deactivates the horizontal and vertical target graphs. See
section 2.3. The available options are

[Sonde Graph].
Activates/deactivates the sonde graph. See section 2.4.

[Temp Graph].
Activates/deactivates the water temperature graph. See section 2.5.

[Bottom Information Graph].
Activates/deactivates the bottom hardness and bottom roughness
graphs. See section 2.6. The available options are

[Alarm] menu.
Activates/deactivates alarms. See section 1.22.

[Bottom Alarm] icon.
Activates/deactivates the bottom (seabed) alarm.

[Fish Alarm] icon.
Activates/deactivates the fish alarm.

[Bottom Fish Alarm] icon.
Activates/deactivates fish alarm for fish near the seabed.

[Water Temperature Alarm] icon.
Activates/deactivates the water temperature alarm.

[Fish Size Graph Alarm] icon.
Activates/deactivates the fish size alarm.

Icon

Description/Options

Menu

Item

Activates/deactivates the vertical target graph.

Activates/deactivates the horizontal target graph

Activates/deactivates the bottom hardness graph.

Activates/deactivates the bottom roughness graph.

Содержание FCV-38

























































































































































Результаты поиска

Содержание FCV-38

Отзывы:

Бренды по названию

Популярные бренды

Furuno FCV-38, Руководство пользователя

Результаты поиска

Содержание FCV-38

Отзывы:

Бренды по названию

Популярные бренды