Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 88

Страница: 88 / 280

2-30

C122-B001-02EN

CHAPTER 2 General Hardware Configuration

2.10

AC Section (ACS)

This section explains the AC section (ACS).

The ACS has a redundant configuration only for the PRIMEQUEST 440 using dual
power feed.

Two power distribution board (PDB) units can be connected to an ACS unit. Three
power supply units (PSUs) can be connected to a PDB.

Two PSUs can be used with one AC cable.

The primary power feed option consists of six PSUs. Up to 12 PSUs can be
connected to the option.

The AC section supports dual power feed as an option.

Table 2.18

lists ACS specifications.

Table 2.18

ACS specifications

Item

Specifications

Input

Voltage

Rated voltage

200 to 240 VAC

Number of phases

Single phase

Fluctuation range

+10% to -10%

Frequency

Rated frequency

50/60 Hz

Fluctuation range

2%, -4%

Содержание PRIMEQUEST 440

























































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 440

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 440, Руководство по проектированию систем

Результаты поиска

Содержание PRIMEQUEST 440

Отзывы:

Бренды по названию

Популярные бренды