manualshive.com logo in svg

Fujitsu PRIMEQUEST 440, Руководство по проектированию систем

Поделиться
Скачать
Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 153

C122-B001-02EN

5-9

 

5.2 Main GSWB Functions

• Support functions

z

Back pressure

 

Back pressure is a method for retaining transmission of a sender by generating a 
dummy collision.  Back pressure can be specified for half-duplex communication.

z

PAUSE frame function

 

The PAUSE frame function sends a PAUSE frame using the MAC control 
mechanism.

 

A PAUSE frame can be specified for full-duplex communication and supports the 
following three modes.
- Two-way control (Symmetric)
- One-way control (Asymmetric:  accept)
- One-way control (Asymmetric:  transmit)

• Restrictions

The restriction list for communication speeds and communication modes is shown 
below.

Table 5.9  Flow control and restriction list

Y:  Supported, N:  Unsupported

Remark: Both functions cannot be executed at the same time.

Communicatio

n speed

Communication mode

Half duplex Full duplex

Back pressure

10 bps

Y

N

100 bps

Y

N

1000 bps

Y

N

PAUSE function

10 bps

N

Y

100 bps

N

Y

1000 bps

N

Y

Содержание PRIMEQUEST 440

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды