manualshive.com logo in svg

Fujitsu PRIMEQUEST 440, Руководство по проектированию систем

Поделиться
Скачать
Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 151

C122-B001-02EN

5-7

 

5.2 Main GSWB Functions

Auto-sense and auto-negotiation functions

The auto-sense and auto-negotiation functions are available.  Auto-sense is a function 
for the port itself, for detecting the speed of a connected unit.  Auto-negotiation, 
which is a protocol between two units stipulated in IEEE802.3u, sets the 
communication speed, the communication mode (full duplex or half duplex), and 
whether to use the flow control function.  If units, both of which have the auto-
negotiation function, are connected to each other, the common mode is determined in 
accordance with the priority stipulated in IEEE802.3u.

• Interface support

The table below lists whether interfaces have the auto-negotiation function.

Table 5.6  Interface support for auto-negotiation

Y:  Supported

N:  Unsupported

• Setting priority

The table below lists the setting priority for auto-negotiation.

Table 5.7  

Auto-negotiation priority 

LAN type

Location

Interface

Auto-negotiation 

function

Remarks

Business 
LAN

Front

1000 BASE-T

Y

BackPlane SerDes

N

Communication speed: 
1 Gbps (fixed)
Communication mode:  
Full duplex (fixed)

Priority

Communication 

speed

Communication 

mode

1

1 Gbps

Full duplex

2

Half duplex

3

100 Mbps

Full duplex

4

Half duplex

5

10 Mbps

Full duplex

6

Half duplex

Содержание PRIMEQUEST 440

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды