manualshive.com logo in svg

Fujitsu PRIMEQUEST 440, Руководство по проектированию систем

Поделиться
Скачать
Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 76

2-18

C122-B001-02EN

CHAPTER 2 General Hardware Configuration

 

2.3.6

PCI segment mode and PCI bus mode

PRIMEQUEST supports two PCI bus mapping modes:  PCI segment mode and PCI 
bus mode.

z

PCI segment mode

 

All PCIU interfaces of each IO_Unit can be used.

z

PCI bus mode

 

Of the PCIU interfaces of each IO_Unit, only PCI Slot#0 and PCI Slot#1 can be 
used.

The mapping mode can be defined for each partition.

Table 2.11 lists the PCI bus mapping modes supported by each operating system.

Table 2.11   PCI bus mapping modes

*1

Fujitsu recommends the PCI segment mode when Red Hat Enterprise Linux is 
used.

OS

PCI segment mode

PCI bus mode

Red Hat Enterprise Linux

Supported (*1)

Supported

Windows Server 2003, Enterprise Edition

Unsupported

Supported

Windows Server 2003. Datacenter Edition

Unsupported

Supported

Содержание PRIMEQUEST 440

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды