manualshive.com logo in svg

Fujitsu PRIMEQUEST 440, Руководство по проектированию систем

Поделиться
Скачать
Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 174

5-30

C122-B001-02EN

CHAPTER 5 Business LAN Management by GSWB

 

*3

Speed on one side is fixed to 10 Mbps and Speed on the other side is fixed to 
100 Mbps.

 

Linkup may be successful on the side fixed to 10 Mbps but normal 
communication is disabled.  Match the Speed settings on both sides when the 
fixed setting is used.

5.3.5

Flow control

Flow control setting

IEEE802.3x flow control is supported for full duplex communication, and 
backpressure flow control is supported for half-duplex communication.

Note, however, that IEEE802.3x flow control operates differently depending on the 
result of the auto-negotiation.

Table 5.20  Flow control setting

Notes on using flow control

Note that enabling the flow control may affect the transfer of other ports because the 
flow control is also performed between GSWB internal chips.

In the sample configuration shown below, the transfer from IOU 0 0 to 
GigabitEthernet 0/6 enables flow control and then a PAUSE frame is sent from 
BCM5692 #1 to BCM5692 #0 to restrict the transfer from BCM5692 #0 to BCM5692 
#1.  Enabling the flow control thus affects the transfer from IOU 3 1 to IOU 4 0.

Flow control setting

Interface Speed setting

Fixed (10/100)

Auto-negotiation

Receive

ON

Enabled

Result of auto-negotiation

OFF

Disabled

Disabled

Send

ON

Enabled

Result of auto-negotiation

OFF

Disabled

Disabled

Содержание PRIMEQUEST 440

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды