Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 160

Страница: 160 / 280

5-16

C122-B001-02EN

CHAPTER 5 Business LAN Management by GSWB

Table 5.12 How transmission and receiving are handled depending on port setting

statuses and frame types

Remark 1: If the port is down, all transmission and reception is impossible.

Remark 2: The port VLAN ID (PVID) identifies the VLAN to be allocated when an

interface belonging to a tag VLAN receives a frame without a tag.

If a tag VLAN is specified for the interface, a frame without a VLAN tag, as
indicated by PVID, can be received.

If a tag VLAN is specified for the interface, a frame without a VLAN tag, as
indicated by PVID, can be transmitted.

Port status

Frame type

Port VLAN

Tag VLAN

PVID

(at tag VLAN)

DOWN

With a
receive
VLAN tag

The same VLAN
ID as port
specification

Unavailable
(discard)

Available

VLAN ID different
from port
specification

Unavailable
(discard)

Without a
receive
VLAN tag

Available

Unavailable
(discard)

Available
(*1)

With a
transmission
VLAN tag

The same VLAN
ID as port
specification

Unavailable -

Available

Unavailable -

VLAN ID different
from port
specification

Unavailable -

Without a
transmission
VLAN tag

Available

Unavailable -

Available

(*2)

Содержание PRIMEQUEST 440

























































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 440

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 440, Руководство по проектированию систем

Результаты поиска

Содержание PRIMEQUEST 440

Отзывы:

Бренды по названию

Популярные бренды