Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 280

Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 42

1-10

C122-B001-02EN

CHAPTER 1 PRIMEQUEST Overview

1.2.1.4 System Mirror

System Mirror duplicates the address cross bar and data cross bar, the inside of the
chip set, and memory. Thus, even if a duplicated component fails, its mirror, the
normal component, can continue the system processing. The use of System Mirror
can thus increase reliability and improve continuity of business.

For example, even when a memory failure occurs, the side containing the faulty
memory can be stopped but the operation can be continued by using normal memory.
Thus, the entire system is not stopped and the operation can be continued.

System Mirror can be switched using the MMB Web-UI.

When System Mirror is not being used, only the address cross bar is duplicated.
Memory is not duplicated and up to the maximum amount of memory space can be
used.

To use System Mirror, a license key (optional product) is required.

For details of System Mirror, see Section

6.3, "System Mirror."

Figure 1.5 System Mirror

Remarks: This function is different from disk mirroring (RAID1), which writes data to

two hard disk drives at the same time. For disk mirroring, see Section

"Redundancy of an HDD (Use of PRIMECLUSTER GDS)."

Improved business continuity with System Mirror

The PRIMEQUEST System Mirror greatly improves business continuity.

shows a comparison of operation with and without System Mirror. In

operation without System Mirror, if a hardware failure occurs while the system is
operating, the system (task) stops. Then, the cause of the failure is investigated,
which is followed by repair work and other processing. Finally, the system is
recovered and restarted. The task remains stopped throughout this period.

System mirror mode

Crossbar

MMB

#0

MMB

#1

IOU

#1

IOU

#2

IOU

#3

IOU

#4

IOU

#5

IOU

#6

IOU

#7

SB
#1

SB#0

SB
#2

SB
#3

SB
#4

SB
#5

SB
#6

SB
#7

IOU#0

- Duplicated chipset and

memory writin

- Interconnect

(address bus/data bus)

duplication

«
...
40
41
42
43
44
...
»

Содержание PRIMEQUEST 440

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды