Franklin Electric CERUS X-DRIVE CXD-003A-4V, Инструкция по установке и эксплуатации

Страница: 207 / 252

PARAMETER REFERENCE TABLES
Parameter Descriptions > VFD Menu
207
VFD-24 0280 Y DEC-4 Time 0.0 to 6000 sec VFD will switch to ACC/DEC4 when DIs set to XCEL-L and XCEL-M are activated.
VFD-25 0281 Y S Start Time 1 0.0 to (variable) sec ACC S-Curve Start starting Time-1
VFD-26 0282 Y S Start Time 2 0.0 to (variable) sec ACC S-Curve Start ending Time-2
VFD-27 0283 Y S End Time 1 0.0 to (variable) sec DEC S-Curve End starting Time-1
VFD-28 0284 Y S End Time 2 0.0 to (variable) sec DEC S-Curve End ending Time-2
VFD-29 0285 N Skip Freq1 High 0.0 to 599 Hz Used to bypass mechanical system resonance frequencies. If the received
speed reference is in the skip zone, VFD will run at
Low Skip Freq
until speed
reference is at or above
High Skip Freq
. Then, speed will be ramped up based
on acceleration time.
VFD-30 0286 N Skip Freq1 Low 0.0 to 599 Hz Low frequency in skip zone 1.
VFD-31 0287 N Skip Freq2 High 0.0 to 599 Hz High frequency in skip zone 2.
VFD-32 0288 N Skip Freq2 Low 0.0 to 599 Hz Low frequency in skip zone 2.
VFD-33 0289 N Skip Freq3 High 0.0 to 599 Hz High frequency in skip zone 3.
VFD-34 0290 N Skip Freq3 Low 0.0 to 599 Hz Low frequency in skip zone 3.
VFD-35 0291 N VFD Duty Select 0_Variable Torque
1_Constant Torque
0_Variable Torque (Light Duty)
1_Constant Torque (Normal Duty)
VFD Rated Amps [VFD-47] and Over-Current levels [PROT-07 ~ PROT-08] are affected
by this setting.
VFD-36 0292 Y Reset Restart 0_Disable
1_Enable
The VFD will automatically initiate operation once fault is cleared and run
command is received.
VFD-37 0293 Y DC Brake CurLvl 0.0 to 100% Level of DC Brake Current output to the motor during start-up and stopping.
VFD-38 0294 Y DC Time at Run 0.0 to 60 sec Duration of the DC Brake current after a run command to apply DC current
to motor to force stop motor for a stable start.
VFD-39 0295 Y DC Time at Stop 0.0 to 60 sec Duration of the DC Brake current after a stop command to apply DC current
to the motor in order to force stop the motor.
VFD-40 0296 Y DC Stop Freq 0.0 to [SET-23] (Hz) Frequency when DC Brake will begin during deceleration.
VFD-41 0297 Y Dwell T at Acc 0.0 to 600 sec When output frequency reaches [VFD-42] during acceleration, VFD will hold
output at [VFD-42] for [VFD-41] timer duration. When timer expires, VFD will
continue acceleration.
VFD-42 0297 Y Dwell Hz at Acc 0.0 to [SET-23] (Hz) VFD holds output frequency at [VFD-42] during Dwell Timer
VFD-43 0299 Y Dwell T at Dec 0.0 to 600 sec When output frequency reaches [VFD-44] during deceleration, VFD will hold
output at [VFD-44] for [VFD-43] timer duration. When timer expires, VFD will
continue deceleration.
VFD-44 0300 Y Dwell Hz at Dec 0.0 to [SET-23] (Hz) VFD holds output frequency at [VFD-44] during Dwell Timer
VFD-45 0301 Y Hopping Carrier 0_Disable
1_Enable
When enabled, VFD will automatically change carrier frequency from 2 to
5kHz (Depends on the drive frame size) in a predetermined offset pattern to
minimize audible noise from the motor. [VFD-58] determines a duration of
each frequency segment.
CODE Mod
Bus AR Display Name
Range Description
Frequency
[VFD-26]
[VFD-27]
[VFD-25] [VFD-28]
Time
60 Hz
Hz
elevados
Salto
Hz bajos
Zona de salto
de resonancia
0