Franklin Electric CERUS X-DRIVE CXD-003A-4V, Инструкция по установке и эксплуатации

Страница: 217 / 252

PARAMETER REFERENCE TABLES
Parameter Descriptions > ADVANCE Menu
217
ADV-06 0774 Y Acc/Dec Type 0_Linear Acc/Dec
1_Auto Acc/L-Dec
2_L-Acc/Auto Dec
3_Auto Acc/Dec
4_Lin, Auto Stall
Provides automated acceleration and deceleration with stall prevention.
0_Linear Acc/Dec: Accelerates and decelerates according to the setting of
[SET-11] ~ [SET-12] and [VFD-19] ~ [VFD-24] .
1_Auto Acc/L-Dec: Auto detects the load torque and accelerates for the
fastest acceleration time and smoothest start current. Deceleration is linear
according to setting of [SET-11] ~ [SET-12] and [VFD-19] ~ [VFD-24] .
2_L-Acc/Auto Dec: Linear acceleration according to setting [SET-11] ~ [SET-12]
and [VFD-19] ~ [VFD-24] . Auto detects the load re-generation and stops the
motor smoothly with the fastest decel time.
3_Auto Acc /Dec: Auto detects load for smoothest operation for accelera -
tion and deceleration.
4_Lin, Auto Stall: Stall prevention by auto accel./decel being limited by
[SET-11] ~ [SET-12] and [VFD-19] ~ [VFD-24] .
ADV-07 0775 N Acc/Dec Format 0_Unit 0.01 sec
1_Unit 0.1 sec
Precision of acceleration and deceleration time
ADV-08 0776 Y Energy Saving 0_Disabled
1_Enabled
When the output frequency is constant, the output voltage will auto
decrease to decrease power consumption.
ADV-09 0777 Y E-Saving Gain 10 to 1000% Determines speed of adjusting output voltage in relationship to load reduc -
tion. If the motor oscillates or has a quick temperature rise, the value should
be increased.
ADV-10 0778 N MMC Mode 0_Disabled
1_Equal Run Time
2_Soft Start mode
3_Lead-Lag
4_Run Time Alt
5_Rotate Lead
Type of operation for Multi-Motor Control.
NOTE:
3_Lead-Lag is the most common multi-pump control mode.
ADV-11 0779 N Motor Quantity 1 (default) to 7 Number of motors in MMC relay control setup. Limit is 3 without I/O card.
When I/O card is installed, selections 1 to 7 are available.
ADV-12 0780 N Aux Mtr Stop Hz 0 to [SET-23] Auxiliary Motor Stop Hertz: When output frequency is less than value and
remains for duration of [ADV-15] , motors will be shut down one by one.
ADV-13 0781 N Alt Run Time 0 to 60000 min Duration of running a motor before switching to another motor.
ADV-14 0782 N S-Start ON Dly 0 to 3600 sec Delay time before switching motor from VFD to power line.
ADV-15 0783 N S-Start Off Dly 0 to 3600 sec Delay time before switching motor from power line to VFD.
ADV-16 0784 Y Mtr Switch Tmr 0 to 3600 sec When timer expires, the system will start preparing to switch motors.
ADV-17 0785 Y Mtr Switch Hz [SET-22] to [SET-23] (Hz) When the output frequency reaches value, the system will start preparing to
switch motors.
ADV-18 0786 Y Lag Start Freq [ADV-23] to [SET-23] Running above this frequency is one of the conditions for starting Lag
pump. Lag Start Frequency parameter is used for [ADV-10] selection
3_Lead-Lag MMC control. Default= 59.50Hz.
ADV-19 0787 Y Lag Start Delay 0 to 600 sec Sets a delay time to start Lag pump when both frequency and pressure con -
ditions are met.
ADV-20 0788 Y Lag Start Level 0.1 to 10% Sets percentage of PID F/B Max [SET-20] value to determine MMC Below Set -
point level for Lag pump starting. This parameter is used for [ADV-10] selec -
tion 3_Lead-Lag MMC control.
ADV-21 0789 Y Lead Freq Drop 0.0 to [SET-23] (Hz) PID High Frequency Limit drop value with MMC Decel Time [ADV-22] at Lag
pump start to prevent system overpressure condition. This parameter is
used for [ADV-10] selection 3_Lead-Lag MMC control.
ADV-22 0790 Y MMC Decel Time 0 to 600 sec Sets deceleration time for PID High Frequency limit value change from High
Freq Limit [SET-23] to ( [SET-23] - [ADV-21] ) at Lag pump start. This parameter is
used for [ADV-10] selection 3_Lead-Lag MMC control.
ADV-23 0791 Y Lag Stop Freq [SET-22] to [ADV-18] (Hz) Running below this frequency is one of the conditions for stopping Lag
pump. This parameter is used for [ADV-10] selection 3_Lead-Lag MMC control.
ADV-24 0792 Y Lag Stop Delay 0 to 600 sec Sets delay time to stop Lag pump when both frequency and pressure condi -
tions are met. This parameter is used for [ADV-10] selection 3_Lead-Lag MMC
control.
ADV-25 0793 Y Lag Stop Level 0.1 to [ADV-20] (%) Sets percentage value of PID F/B Max [SET-20] value to determine MMC At Set -
point level for Lag pump stopping. This parameter is used for [ADV-10] selec -
tion 3_Lead-Lag MMC control.
CODE Mod
Bus AR Display Name
Range Description