Foma PushTalk SH902i, Руководство пользователя

Страница: 540 / 568

538
Ap
p
e
n
d
ix
/U
si
n
g
w
ith
Extern
al
Devi
ces/
T
ro
u
b
lesh
o
o
ti
n
g
S
o
ft
w
a
re Up
d
a
te
Information stored in your FOMA terminal, such as the total call charges and the ON/OFF
settings of various functions, may be cleared or reset if your FOMA terminal is damaged,
repaired, or mishandled.
If this occurs, please re-enter the information or re-specify the settings.
If your FOMA terminal gets wet or has been in a humid location, turn off the power, take out
the battery immediately, and bring it to a repair counter that DoCoMo specifies as soon as
possible. However, depending on the condition, repairs may not be possible.
The FOMA terminal earpiece and speakers contain parts that generate magnetic waves. Keep ATM cards and
other objects likely to be affected by magnetic waves away from the FOMA terminal. Cards may become unusable.
Check for FOMA terminal software updates. If necessary, use packet transmission
*
to
download software and update.
* There is no packet transmission charge for updating software.
Check the DoCoMo web page or
お知らせ＆ヘルプ
(News & Help) on iMenu for updates.
When updating, select Now update or Reserve .
Now update: Update immediately.
Reserve: Software updates automatically on set date and time.
Software is updated even when host for i-mode is changed to a custom host.
Recharge battery before updating software.
Software cannot be updated during the following conditions.
Date and time are not set Battery icon is
#
or
$
During a call/Outside the service area While in Self mode Connected to an external device
All lock is set PIM is locked
If PIN code is set to ON and software is updated, PIN code input screen appears after automatic reload.
Correct PIN code must be entered to make/receive calls and use other communications functions.
Downloading and rewriting software may take time.
Other functions cannot be used while updating. (Receiving voice calls is possible.)
While updating software, received i-mode mail and Message R/F are held at i-mode center. Received SMS is
held at SMS center.
If i-mode mail or Message R/F is held at i-mode center,
W
/
G
/
I
appears but will disappear when software is
reloaded after update. In addition, even if Receive option is set to ON and mail is received during software
update, notices may not appear on the display after update is completed. Mail and messages are held at
i-mode center.
During software update, the handset makes an SSL connection with the server (DoCoMo site). Set the Root
Certificate to valid. (The default setting is
Enable .
n
P. 248.)
It is recommended to update software at a location with a strong signal (three bars for the antenna icon).
If signal status becomes weak or download is interrupted when downloading software, update software
again in a location with good signal conditions.
If software has already been uploaded, No update is needed. Please continue to use as before appears
when software update is checked.
When updating software, information about handset (model and serial number) is sent to the server (DoCoMo
software update server). Sent information is only used for software update.
Do not remove the battery pack while the software is updating. Failure to update software may occur.
Software can be updated even if handset contains phonebook, camera or download data. However, DoCoMo
cannot protect data that could be lost due to malfunction, damage, water leakage and so on. It is
recommended that important data be backed up (
n
P. 380, P. 522) before updating. (Note that some data,
such as downloaded data, cannot be backed up.)
If software update fails, Rewrite failed appears and all operations are not available. In this case, bring FOMA
terminal to a repair counter that DoCoMo specifies.
Software Update
Updating Software
dv30̲e.book Page 538 Tuesday, November 22, 2005 3:21 PM