Foma PushTalk SH902i, Руководство пользователя

Страница: 330 / 568

328
i-
a
pp
li
Au
to
S
tart
There are three methods to automatically start
i-
a
ppli.
Set date and time in advance. (
n
P. 48)
The default setting is OFF .
1
In stand-by, press
i
for 1+
seconds, press
4
[Auto start].
Alternatively, select
,
(i-
α
ppli)
→
Auto start
from Top menu.
2
Press
1
[ON].
Auto start is set.
J
Setting software startup time with
FOMA terminal settings
1
In the auto start screen (see above),
press
3
[Details set] and select a
number.
Auto start software list appears.
2
Select software, press
t
, and set
the start date and time.
Use 24-hour format.
Move the cursor with
w
.
J
Enabling Auto start setting for
supported software
In the schedule setting screen,
press
4
[Time interval].
To disable, delete Auto start setting. (“To delete
Auto start schedule” in step 1 of “
J
Setting
software startup time with FOMA terminal
settings”)
Time interval appears in gray for software
without Auto start settings.
Packet transmission charges apply when using this
service.
Refer to “i-mode User’s Manual” for details on
G-GUIDE program schedule remote control.
Auto Start
Running i-
a
ppli Automatically
Auto start using
the i-
α
ppliDX
setting
Set Auto start to ON to enable.
Auto start using
the software
function Auto start setting pre-installed in
software. Set Auto start to
ON and
register software to enable. Register
up to nine.
Auto start using
the FOMA
terminal setting Set time, date and day for i-
α
ppli saved
in FOMA terminal to set Auto start. Set
Auto start to
ON and set schedule to use.
Register up to nine.
Configuring Auto Start
<Auto Start>
To save new
Auto start
schedule Select number
→ t
.
To save a new schedule,
select a slot with
----------------- .
To change Auto
start schedule Select a number to change
→
t → 1
[Update].
To delete Auto
start schedule Select a number to delete
→
t → 2
[Delete].
Note
Auto start screen
To start daily Press
1
[Daily]
→
enter time
→ t
.
To start on set
day of week Press
2
[Select day]
→
select
day of week
t
(repeatable)
→
C
[Confrm]
→
enter time
→ t
.
To start on set
date Press
3
[Set date]
→
enter
date and time
→ t
.
Note
If Auto start cannot be started, the error is recorded
in Auto start error history.
Automatic startup is not available in the following
situations:
Handset is turned off
Other functions are activated
i-
α
ppli is running
Call is in progress
Auto start time is the same as alarm time of
Schedule or ToDo list
i-
α
ppli PIM is locked
The functions below operate with the following
priority when the same time is set.
Reset settings (
n
P. 437) disables i-
α
ppli Auto
start setting.
If transmission setting for software with Auto start settings
is set to
Always confirm , a transmission confirmation
screen appears upon startup. If no operations are
performed for five seconds, software starts automatically
as if
No was selected in confirmation screen.
When two Auto start times for the same software are
set within ten minutes of each other, Auto start does not
function. Set Auto start time interval to ten minutes or
more.
Run error appears in the Auto start error history.
Schedule setting
screen
Priority (high
→
low)
Function Auto power OFF
→
Auto power ON
→
Alarm
→
ToDo list
→
i-
α
ppli Auto start
dv30̲e.book Page 328 Tuesday, November 22, 2005 3:21 PM