Fluke CombiScope PM3370B Скачать руководство пользователя страница 108

Страница: 108 / 133

PERFORMANCE TEST

4 - 33

Only the timebase positions that are essential for instrument accuracy are
checked.

DEL’D TB TIME/DIV is electrically coupled to MAIN TB TIME/DIV; to check the
settings in the table press only the MAIN TB TIME/DIV VAR keys.

equirements for analog mode MAGNIFY off (

1):

DEL’D TB setting

MAIN TB setting Marker pulse

Max. error

5.00

0.5 ms

1.8%

20.0

1.8%

5.00

1.8%

1.00

1.8%

500 ns

0.5

1.8%

100 ns

0.1

1.8%

50.0 ns

50 ns

1.8%

20.0 ns (PM3390B/94B)

20.0 ns

20 ns

1.8%

Requirements for analog mode MAGNIFY on (

10):

DEL’D TB setting

MAIN TB setting Marker pulse

Max. error

100 ns

0.1

2.3%

10.0 ns

10 ns

2.3%

5.00 ns

5 ns

3.3%

2.00 ns (PM3390B/94B)

2.00 ns

2 ns

3.3%

4.3.28

Horizontal deflection; delay time multiplier

In this test the minimum and maximum delay time is checked.

Test equipment:

None

Settings/procedure and requirements:

Press the AUTOSET key.

Press the DTB menu key and select DEL’D TB ’on’ and MAIN TB ’on’ from
the appropriate menu .

Set MAIN TB to 500 ns.

Set DEL’D TB to 50.0 ns.

Separate the MAIN TB and DEL’D TB traces with the TRACK control.

Adjust the delay time to 500.0 ns using of the DELAY control (in the
DELAYED TIMEBASE section).

Adjust the start of the MAIN TB display exactly on the first graticule line by
using the X POS control (at maximum TRACE INTENSITY).

Содержание CombiScope PM3370B






































































































































Результаты поиска

Содержание CombiScope PM3370B

Отзывы:

Похожие инструкции для CombiScope PM3370B

Бренды по названию

Популярные бренды

Fluke CombiScope PM3370B, Справочное руководство

Результаты поиска

Содержание CombiScope PM3370B

Отзывы:

Похожие инструкции для CombiScope PM3370B

Бренды по названию

Популярные бренды