Fluke CombiScope PM3370B Скачать руководство пользователя страница 114

Страница: 114 / 133

PERFORMANCE TEST

4 - 39

Test set-up:

Settings/procedure and requirements:

Apply a 100 MHz sine-wave signal of 1 V(pp into 50

Ω

) from the SG 503 to

input CH1.

Press the AUTOSET key and set CH1 to 0.5V/div.

Use a 50

Ω

termination. For instruments with switchable 50

Ω

input

impedance it is recommended to make use of this feature (via
VERT MENU key).

Set the input coupling of CH1 to DC and POSition the signal in the vertical
center of screen.

Select ’trig’ from in the menu under the TB MODE mode key.

Press the TRIGGER menu key and select level-pp ’off’ and ’dc’ trigger
coupling from the TRIGGER MAIN TB menu

Adjust TRIGGER LEVEL for a correctly triggered display.

Decrease the amplitude of the input signal.

Verify that the signal is well-triggered at amplitudes of 0.6 divisions and more.

10 -

Decrease the input frequency to 50 kHz.

11 -

Verify that the signal stays well-triggered at amplitudes of 0.6 divisions and
more.

12 -

Increase the input frequency to 200 MHz.

13 -

Increase the input voltage to 1.2 division.

14 -

Turn TRIGGER LEVEL.

15 -

Verify that the signal is well-triggered at amplitudes of 1 division and more.

16 -

Apply a 300 MHz sine-wave signal of 2V (pp into 50

Ω

) from the SG 504 to

input CH1.

17 -

Adjust the input voltage to 2 divisions. Signal must be in vertical center of
screen.

18 -

Verify that the signal is well-triggered at amplitudes of 2 divisions and
more; adjust TRIGGER LEVEL when necessary.

Содержание CombiScope PM3370B






































































































































Результаты поиска

Содержание CombiScope PM3370B

Отзывы:

Похожие инструкции для CombiScope PM3370B

Бренды по названию

Популярные бренды

Fluke CombiScope PM3370B, Справочное руководство

Результаты поиска

Содержание CombiScope PM3370B

Отзывы:

Похожие инструкции для CombiScope PM3370B

Бренды по названию

Популярные бренды