Fluke CombiScope PM3370B Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 133

background image

PERFORMANCE TEST

4 - 41

6

-

Press the TRIGGER menu key and select level-pp ’off’ and ’dc’ trigger
coupling from the TRIGGER MAIN TB menu

7

-

Adjust TRIGGER LEVEL for a correctly triggered display.

8

-

Decrease the amplitude of the input signal.

9

-

Verify that the signal is well-triggered at amplitudes of 0.6 divisions and
more.

10 -

Decrease the input frequency to 50 kHz.

11 -

Verify that the signal stays well-triggered at amplitudes of 0.6 divisions and
more.

12 -

Increase the input frequency to 100 MHz (60 MHz).

13 -

Increase the input voltage to 1.2 division.

14 -

Turn TRIGGER LEVEL.

15 -

Verify that the signal is well-triggered at amplitudes of 1.2 division and
more.

16 -

Increase the input frequency to 200 MHz (150 MHz).

17 -

Adjust the input voltage to 2 divisions. Signal must be in vertical center of
screen.

18 -

Verify that the signal is well-triggered at amplitudes of 2 divisions and
more; adjust TRIGGER LEVEL when necessary.

PM3384B: repeat the procedure for CH2, CH3 and CH4 for the frequencies
50 kHz (0.6 division input signal) and 200 MHz (2 division input signal).
PM3370B/80B: repeat the procedure for CH2 and the EXT TRIG input for the
frequencies 50 kHz (0.6 division input signal) and 200 MHz (150 MHz) (2 division
input signal).
Press the ANALOG key (’DIGITAL MODE’ is displayed briefly) and repeat the
tests in this chapter for the digital mode.
Press the ANALOG key (’ANALOG MODE is displayed briefly) to return to analog
mode.

4.3.36

MAIN TB/DEL’D TB triggering; trigger sensitivity TVL-TVF

This test checks the trigger sensitivity for television line- and field synchronization
pulses.

Test equipment:

TV pattern generator with video output (PM 5418)

«
...
114
115
116
117
118
...
»

Содержание CombiScope PM3370B






































































































































Отзывы:

Нет отзывов

Похожие инструкции для CombiScope PM3370B

Бренд: Nitecore Страницы: 4

Бренд: LAZBOY Страницы: 9

Бренд: M-Audio Страницы: 3

Web Riderz MM00124 Web Swing

Бренд: M&M Sales Enterprises Страницы: 2

Бренд: Olympus Страницы: 56

QNET Physics and Dynamics

Бренд: Quanser Страницы: 4

Бренд: Mach Страницы: 12

TITAN 2967-033A

Бренд: Yetter Страницы: 20

Бренд: Garmin Страницы: 2

Бренд: Kamar Страницы: 2

Бренд: PARAMOUNT BED Страницы: 120

Бренд: Nakayama Страницы: 19

Бренд: WAGNER Страницы: 31

Бренд: Trigano Страницы: 4

Einthoven CR1000

Бренд: ACE Solution Страницы: 29

Bug Zappers BZ-15

Бренд: Black Flag Страницы: 2

MEGA STROBE/DMX

Бренд: American DJ Страницы: 2

Бренд: Bauerfeind Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды