Fluke CombiScope PM3370B Скачать руководство пользователя страница 71

Страница: 71 / 133

BRIEF CHECKING PROCEDURE

3 - 9

Press the left of the DELAYED TIMEBASE TIME/DIV keys and verify that the
number of the displayed signal periods increases. The lowest TIME/DIV range
is 100

s/division.

Press the right of the DELAYED TIME BASE TIME/DIV keys and verify that
the number of displayed periods increases. Proceed until the time scale of
50

s/division is reached.

Select ’trig’d’ from the DELAYED TIME BASE menu.

Press the front panel key TRIG1 if the DELAYED TIMEBASE is not triggered
on CH1. This is indicated in the lower right corner of the display.

Use the

∆

control to adjust the trigger level of DELAYED TIMEBASE for

a triggered display (signal on DEL’D TB time scale visible).

MAIN TB trigger slope and time coeficients in digital mode:
-

Press the ANALOG key (’DIGITAL MODE’ is displayed briefly). The
oscilloscope is now in digital mode.

Press the AUTOSET key.

Adjust the AMPL keys to an input sensitivity of 100 mV/division.

Adjust the MAIN TB TIME/DIV keys to 100

s/DIV.

Press the TRIG1 key and verify that the displayed square wave starts with a
negative going signal.

Press the TRIG1 key and triggering on the positive slope is obtained again.

Press the left side of the MAIN TB TIME/DIV keys and verify that the number
of signal periods increases.

Select 500

s/division and verify that one signal period is displayed per

division.

Press the right side of the MAIN TB TIME/DIV keys and verify that the number
of signal periods decreases.

Use the MAIN TB TIME/DIV to select 20.0

s/division.

ST6655

CH1 0.2V

MTB ...
DTB ...

400

DELAY TB DISPLAY

MAIN TB DISPLAY

POS

TRACK

Figure 3.9

Содержание CombiScope PM3370B






































































































































Результаты поиска

Содержание CombiScope PM3370B

Отзывы:

Похожие инструкции для CombiScope PM3370B

Бренды по названию

Популярные бренды

Fluke CombiScope PM3370B, Справочное руководство

Результаты поиска

Содержание CombiScope PM3370B

Отзывы:

Похожие инструкции для CombiScope PM3370B

Бренды по названию

Популярные бренды