Fluke CombiScope PM3370B Скачать руководство пользователя страница 93

Страница: 93 / 133

4 - 18

PERFORMANCE TEST

Test set up:

Settings/procedure:

Apply a 200 MHz (PM3390B/94B), 100 MHz (PM3380B/84B) or 60 MHz
(PM3370B) sine-wave signal of 0.8 V(pp into 50

Ω

) to input CH1.

Press the AUTOSET key.

Use a 50

Ω

termination. Use the internal termination when available.

Switch all channels ON. PM3370B/80B/90B: switch CH2 on.

Set all channels to 0.1 V/div.

Adjust the generator to a signal amplitude of 8 div.

Activate the GND function of CH2, CH3, and CH4. PM3370B/80B/90B:
activate GND of CH2.

Requirements:

Verify that the displayed amplitude the channels with no input signal applied
is less than 0.16 divisions, (better than 50:1).

Repeat the above settings and procedure for PM3384B/94B:
-

Input signal applied to CH2. CH1, CH3, and CH4 input GND.

Input signal applied to CH3. CH1, CH2, and CH4 input GND.

Input signal applied to CH4. CH1, CH2, and CH3 input GND.

Repeat the above settings and procedures for PM3370B/80B/90B:
-

Input signal applied to CH2. CH1 input GND.

For all models:
-

Press the ANALOG key (’DIGITAL MODE’ is displayed briefly) and repeat the
tests in this chapter for the digital mode.

Press the ANALOG key (’ANALOG MODE’ is displayed briefly) to return to
analog mode.

Содержание CombiScope PM3370B






































































































































Результаты поиска

Содержание CombiScope PM3370B

Отзывы:

Похожие инструкции для CombiScope PM3370B

Бренды по названию

Популярные бренды

Fluke CombiScope PM3370B, Справочное руководство

Результаты поиска

Содержание CombiScope PM3370B

Отзывы:

Похожие инструкции для CombiScope PM3370B

Бренды по названию

Популярные бренды