Fluke CombiScope PM3370B Скачать руководство пользователя страница 107

Страница: 107 / 133

4 - 32

PERFORMANCE TEST

Test set-up:

Settings/procedure:

Apply a 0.5 ms time marker signal to input CH1.

Press the AUTOSET key.

Use a 50

Ω

termination. For instruments with switchable 50

Ω

input

impedance it is recommended to make use of this feature (via
VERT MENU key).

Press the TRIGGER menu key.

Select level-pp ’off’ and ’dc’ trigger coupling from the TRIGGER MAIN TB
menu.

Press the TB MODE menu key and select ’trig’ from the related menu.

Adjust TRIGGER LEVEL for a correctly triggered display.

Set the trace height to about 4 divisions.

Press the DTB menu key and select DEL’D TB ’on’ and MAIN TB ’on’ from
the related menu .

10 -

Set MAIN TB to 1.00 ms and DELAYED TIME BASE to 5.00

11 -

Use the DELAY control (in the DELAYED TIMEBASE SECTION to set the
time delay to about 0 seconds.

12 -

Adjust the vertical position of the MAIN TB display with the CH1 POS
control in the top half of the viewing area.

13 -

Adjust the vertical position of the DELAYED TIMEBASE display with the
TRACK control.

14 -

Verify the DELAYED TIMEBASE deflection coefficients with MAGNIFY off
(

1) and MAGNIFY on (

10) according to the requirements in the tables.

Use the deflection error facility of the time marker generator.

Note:
-

Error limits must be measured between the 2nd and the 10th graticule line
(there are 11 graticule lines). These are the central 8 divisions.

With MAGNIFY on (

10), the central 10 divisions of the expanded 100

divisions of DEL’D TB are measured.

Содержание CombiScope PM3370B






































































































































Результаты поиска

Содержание CombiScope PM3370B

Отзывы:

Похожие инструкции для CombiScope PM3370B

Бренды по названию

Популярные бренды

Fluke CombiScope PM3370B, Справочное руководство

Результаты поиска

Содержание CombiScope PM3370B

Отзывы:

Похожие инструкции для CombiScope PM3370B

Бренды по названию

Популярные бренды