Fluke 522A/6 Скачать руководство пользователя

Страница: 293 / 426

SC600 Oscilloscope Calibration Option

Remote Commands and Queries

9-31

Video Function Commands

VIDEOFMT

(IEEE-488, RS-232, Sequential)
Selects the format for VIDEO mode.

Parameters:

NTSC

PAL

PALM

(for PAL-M), or

SECAM

Example:

VIDEOFMT SECAM

VIDEOFMT?

(IEEE-488, RS-232, Sequential)
Returns the VIDEO mode format.

Parameters: None

Response:

NTSC

PAL

PALM

(for PAL-M), or

SECAM

VIDEOMARK

(IEEE-488, RS-232, Sequential)
Programs the VIDEO mode line marker location.

Parameters: Line

marker

number.

Example:

VIDEOMARK 10

VIDEOMARK?

(IEEE-488, RS-232, Sequential)
Returns the VIDEO mode line marker setting.

Parameters: None.

Response: <character>

SINE

SPIKE

SQUARE

SQ20PCT

Overload Function Commands

OL_TRIP?

(IEEE-488, RS-232, Sequential)
Returns the detected state of scope overload protection.

Parameters: None

Response:

Returns the number of seconds before protection was tripped. Returns 0 if
protection has not been tripped or if OVERLD mode not active.

TLIMIT

(IEEE-488, RS-232, Sequential)
Sets the OPERATE time limit for the OVERLD mode signal. The Calibrator

automatically returns to STANDBY if the UUT protection trips within this interval or at

the end of this interval if the protection has not tripped.

Parameters: 1 to 60 (seconds)

Example:

TLIMIT 30

Содержание 522A/6











































































































































































































































































































































































































































Результаты поиска

Содержание 522A/6

Отзывы:

Похожие инструкции для 522A/6

Бренды по названию

Популярные бренды

Fluke 522A/6, Руководство оператора

Результаты поиска

Содержание 522A/6

Отзывы:

Похожие инструкции для 522A/6

Бренды по названию

Популярные бренды