Fluke 522A/6 Скачать руководство пользователя

Страница: 275 / 426

SC600 Oscilloscope Calibration Option

How to Calibrate the Pulse and Frequency Response on an Oscilloscope

9-13

The Edge Function

The Edge function is used for calibrating the pulse response for your oscilloscope. To

reach the Edge menu, press the softkey under MODE until “edge” appears.

gjh055.eps

You can press the MODE softkey to cycle through the functions in the order shown, or

you can press

to return directly to the SCOPE menu.

Each option in the Edge menus is described below.

•

OUTPUT @ SCOPE terminal (50

)

Indicates the location and impedance of the

signal output. If the signal does not appear on the oscilloscope, press

. To

disconnect the signal, press

You cannot change the output impedance in Edge mode.

•

TD PULSE

Press once to thrn the Tunnel Diode Pulser drive signal on, again to

turn the Pulser drive off. This signal sources up to 100 V p-p to drive a Tunnel Diode

Pulser (Fluke Part Number 606522, Tektronix 067-0681-01, or equivalent.

•

TRIG

If you are using the external trigger, use this key to toggle the trigger off and

on. When on, the reading will show “/1” which indicates that the external trigger is at

the same frequency as the edge output. The external trigger can be useful for many

digital storage oscilloscopes that have difficulty triggering on fast rise time signals.

•

MODE

Indicates you are in Edge mode. Use the softkey to change modes and open

the corresponding menus for the other four oscilloscope calibration modes.

Pulse Response Calibration Procedure for an Oscilloscope

This sample procedure shows how to check the oscilloscope’s pulse response. Before you

check your oscilloscope, see your oscilloscope’s manual for the recommended calibration

settings.
Before you start this procedure, verify that you are running the oscilloscope option in

Edge mode. If you are, the Control Display shows the following menu.

gjh067.eps

Perform the following sample procedure to calibrate the pulse response.

Содержание 522A/6











































































































































































































































































































































































































































Результаты поиска

Содержание 522A/6

Отзывы:

Похожие инструкции для 522A/6

Бренды по названию

Популярные бренды

Fluke 522A/6, Руководство оператора

Результаты поиска

Содержание 522A/6

Отзывы:

Похожие инструкции для 522A/6

Бренды по названию

Популярные бренды