Fluke 522A/6 Скачать руководство пользователя | Manualshive

Страница: 197 / 426

background image

Remote Commands

Command Summary by Function

6

6-9

Table 6-9. Setup and Utility Commands (cont.)

Command Description

REFCLOCK_D?

Returns the power-up and reset default for the reference clock source (internal or
through the 10 MHz IN BNC connector).

REFPHASE_D

If two Calibrators are synchronized using 10 MHz IN/OUT, sets the power-up and reset
default phase difference between the NORMAL terminals on the slave Calibrator and the
NORMAL terminals of the master Calibrator.

REFPHASE_D?

If two Calibrators are synchronized using 10 MHz IN/OUT, returns the power-up and
reset default phase difference between the NORMAL terminals on the slave Calibrator
and the NORMAL terminals of the master Calibrator.

RTD_TYPE_D

Set the default Resistance Temperature Detector (RTD) sensor type.

RTD_TYPE_D? Returns the default Resistance Temperature Detector (RTD) sensor type.

SP_SET

Sets the HOST serial port communication parameters and saves them in nonvolatile
memory.

SP_SET?

Returns the HOST serial port communication parameters contained in nonvolatile
memory.

TC_TYPE_D

Sets the power-up and reset default thermocouple type.

TC_TYPE_D?

Returns the power-up and reset default thermocouple type.

TEMP_STD

Sets the temperature degree standard, ipts-68 or its-90.

TEMP_STD?

Returns the temperature degree standard, ipts-68 or its-90.

TLIMIT_D

Sets the power-up and reset default for the time limit for –SC600 OVERLD mode to stay
in operate.

TLIMIT_D?

Returns the power-up and reset default for the time limit for –SC600 OVERLD mode to
stay in operate.

UNCERT?

Retums specified uncertainties for the present output. If there are no specifications for an
output, returns zero.

Table 6-10. Status Commands

Command Description

ERR?

Returns the first error code with an explanation contained in the Calibrator error queue,
then removes that error code from the queue.

EXPLAIN?

Explains an error code. This command returns a string that explains the error code
furnished as the parameter.

FAULT?

Returns the first error code contained in the Calibrator error queue, then removes that
error from the queue.

FUNC?

Returns the present output, measurement, or calibration function.

ISCE

Loads two bytes into both the Instrument Status 1 to 0 Change Enable register and the
Instrument Status 0 to 1 Change Enable register.

ISCE?

Returns the OR of the contents of the Instrument Status 1 to 0 Change Enable register
and the Instrument Status 0 to 1 Change Enable register.

ISCE0

Loads two bytes into the Instrument Status 1 to 0 Change Enable register.

«
...
195
196
197
198
199
...
»

Содержание 522A/6











































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 522A/6

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: Parker Страницы: 54

Бренд: NORLUX Страницы: 2

Бренд: DBX Bushido Страницы: 12

Бренд: Sable Страницы: 28

bionic power knee

Бренд: Össur Страницы: 2

BALANCE KNEE OM8

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 37

REBOUND DIABETIC WALKER

Бренд: Össur Страницы: 63

Бренд: Össur Страницы: 67

ECHODIA Babyscreen

Бренд: Électronique du Mazet Страницы: 65

Pendalyte 40472U

Бренд: Lightolier Страницы: 3

PulseDose LT PD1000

Бренд: DeVilbiss Страницы: 58

Бренд: Delfield Страницы: 2

Vetter QuickStrut

Бренд: Idex Страницы: 14

Sportsman EXG 14/12

Бренд: M&R Страницы: 98

Бренд: siat Страницы: 102

Бренд: Tarter Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды