Fluke 522A/6 Скачать руководство пользователя

Страница: 386 / 426

5522A

Operators Manual

11-16

I OUT AUX when current is present at the AUX output and I OUT 20A if the current is

present at the 20A output.
In the PQ mode, the operation of the Output Information behaves slightly different than

in the normal operating mode described in Chapter 4. In the Composite Harmonic mode,

the calibrator does not update the Output Information Menu until the waveform is built.

For example, if the calibrator is presently set at 10 A, 60 Hz, with STBY showing in the

Output Display, and the user wishes to output 1 A by pressing “1A

", the Output

Information menu will not automatically change to OUTPUT AUX until



is pressed.

When in the SET WAVE menu, the Output Information Menu is not shown. In those

menus, if



is pressed and the Control Display shows an overcompliance message, it

is because the output location has changed. Clear the message and move the unit under

test to the proper terminals.

& REF Menus

In the Volts and Current Dual Output mode, phase between the voltage and current

outputs can be specified by the user. These menus operate in the same fashion as the

normal dual output mode, as described in Chapter 4.

Composite Harmonics Function (Volts and Volts)

After entering the PQ Mode and accessing Composite Harmonic Function (explained

previously in this section), enter the correct voltages into the calibrator. For example, 1 V

and 2 V. The following menu appears:

nn361f.eps

The V @ NOR and V @ AUX indicators on the Control Display are for information

purposes only. This message is letting the user know that there is voltage present at the

NORMAL or AUX output terminals.
Because the calibrator is now set up to output voltage and current, any previously created

wave is removed. A new wave can be created by pressing the WAVE MENUS blue

softkey. The menu shown below appears.

nn362f.eps

Begin editing either voltage wave by pressing the SET NRM WAVE or SET AUX

WAVE blue softkeys. The Wave Selection Menu shown below appears.

nn353f.eps

Содержание 522A/6











































































































































































































































































































































































































































Результаты поиска

Содержание 522A/6

Отзывы:

Похожие инструкции для 522A/6

Бренды по названию

Популярные бренды

Fluke 522A/6, Руководство оператора

Результаты поиска

Содержание 522A/6

Отзывы:

Похожие инструкции для 522A/6

Бренды по названию

Популярные бренды