Fluke 522A/6 Скачать руководство пользователя

Страница: 288 / 426

5522A

Operators Manual

9-26

Perform the following procedure to test the overload protection of an oscilloscope:
1.

Connect the calibrator to Channel 1 on the oscilloscope.

Select the voltage type (DC or AC) using the OUT VAL softkey.

Key in the voltage level. (The default value is 5 V.)

If necessary, change the duration. (Refer to the procedure described above.) The

default duration is 10s.

Check for test results displayed with the UUTTRIP softkey.

Remote Commands and Queries

This section describes commands and queries that are used specifically for the SC600

Option. Each command description indicates whether it can be used with IEEE-488 and

RS-232 remote interfaces and identifies it as a Sequential, Overlapped, or Coupled

command.

IEEE-488 (GPIB) and RS-232 Applicability

Each command and query has a check

box indicating applicability to IEEE-488 (general purpose interface bus, or GPIB) and

RS-232 remote operations.

Sequential Commands

Commands executed immediately as they are encountered in the

data stream are called sequential commands. For more information, see “Sequential

Commands” in Chapter 5.

Overlapped Commands

Commands

SCOPE

TRIG

, and

OUT_IMP

are designated as

overlapped commands because they may be overlapped (interrupted) by the next

command before they have completed execution. When an overlapped command is

interrupted, it may take longer to execute while it waits for other commands to be

completed. To prevent an overlapped command from being interrupted during execution,

use

*OPC

*OPC?

, or

*WAI

, which prevent interruptions until they detect the

command’s completion. For more information, see “Overlapped Commands” in Chapter

Coupled Commands

SCOPE

and

OUT_IMP

are coupled commands because they can

be coupled (combined) with other commands to form a compound command sequence.

Care must be taken to ensure that commands are not coupled in a way that may cause

them to disable each other, since this may result in a fault. For more information, see

“Coupled Commands” in Chapter 5.

General Commands

Table 9-1 is a list of Scope command parameters.

Table 9-1. SCOPE Command Parameters

Parameter Description/Example

OFF

Turns the oscilloscope hardware off. Programs 0 V, 0 Hz, output at the NORMAL
terminals, standby.

VOLT

Oscilloscope ac and dc VOLT mode. Programs 20 mV peak-to-peak, 1 kHz, output at
the SCOPE BNC, output impedance 1 M

, standby if from OFF or previously in

standby. FUNC? Returns SACV (for ac) or SDCV (for dc).

Example:

SCOPE VOLT; OUT 4 V, 1 kHz
(ac voltage, 4 V peak-to-peak, 1 kHz.)

Содержание 522A/6











































































































































































































































































































































































































































Результаты поиска

Содержание 522A/6

Отзывы:

Похожие инструкции для 522A/6

Бренды по названию

Популярные бренды

Fluke 522A/6, Руководство оператора

Результаты поиска

Содержание 522A/6

Отзывы:

Похожие инструкции для 522A/6

Бренды по названию

Популярные бренды