Flowserve FlowAct 1502 Скачать руководство пользователя страница 72

Страница: 72 / 76

FlowAct Diaphragm Linear Actuator FCD VLENIMFACTA4 10/16

Item #

Part

202

6.1

Diaphragm Casing (4x)

211

6.12

Stem

220

6.14

Disk (2x)

225

6.16

Diaphragm (2x)

227

6.15

Diaphragm Plate (2x)

228

6.13

Spacer Bushing (2x)

229

6.21

Actuator Spring

231

6.22

Distance Plate (2x)

253

6.8

Lower Guide Bushing

254

6.80

Plain Bearing (3x)

255

6.18

Thrust Washer (2x)

258

6.26

Vent Plug (2x)

272

6.17

O-Ring (2x)

273

6.11

Scraper Ring

275

6.10

O-Ring (3x)

276

6.9

O-Ring (4x)

279

6.46

O-Ring (24x)

326

6.23

Spring Adjusting Plate (2x)

334

6.45

Hexagon Bolt (24x)

335

6.3.1

Hexagon Bolt - short (40x)

336

6.3.2

Hexagon Bolt - long (8x)

337

6.5

Plain Washer (48x)

339

6.25

Protection Sleeve (8x)

348

6.20

Stem

349

6.19

Lock Washer (2x)

351

6.4

Hexagon Nut (48x)

373

6.82

Intermediate Guide Bushing

374

6.47

Distance Bushing (2x)

380

6.81

Stem Extension

389

6.83

Upper Guide Bushing

Alternatively, hex head assembled screws with captive flat washers are used for this application.

336

335

337

202

389

254

276

279

334

202

258

279

334

348

374

276

351

339

202

253

254

276

279

334

258

380

349

374

228

227

220

272

225

255

211

202

373

254

276

279

334

273

275

229

326

231

275

Table 39: Actuator parts

Figure 36: Actuator parts

44. Lubricate the new O-ring (272) with an appropriate lubricant.

45. Lower the distance bushing (374), spacer bushing

(228), disk (220), diaphragm plate (227),

diaphragm (225), O-ring (272), thrust

washer (255) and lock washer (349)

onto the stem extension (6.81).

NOTICE

Arrange the distance bushing like an
correctly wearing hat. The internal

stroke stop takes over the special nut.

46. Lubricate the thread of the stem extension (380) with

an appropriate lubricant.

NOTICE

The diaphragm plate should be posi-
tioned to the diaphragm with the aid

of the positioning template. Mark the position.

47. Fix the stem (211) with the stem clamping tool against

twisting.

48. Load the springs by tightening the stem (348) clock-

wise using a suitable torque wrench, see section 15

torque requirements.

NOTICE

We recommend you to use a hy-
draulic spring press, as a minimum

requirement a beam and threaded rods in 8.8 quality
(ISO 898-1) or higher as well as washers and nuts al-
ternatively.

49. Remove the stem clamping tool.

50. Install the diaphragm casing (203), positioning the

casing such that the air connections opposites.

51. Lubricate the threats of the long hexagon bolts (336) with

an appropriate lubricant and load the springs uniformly

in a clockwise sequence by tightening the long hexagon

bolts (336), plain washers (337) and hexagon nuts (351).

52. Install the short hexagon bolts (335), plain washers (337)

and hexagon nuts (351).

53. Tighten the nuts (351) using a crosswise pattern in

four steps, see section 15 torque requirements.

54. Install the protection sleeve (339).

55. Perform 3 full strokes and check the tightening of the

casing bolting.

56. Log the maintenance interval and the work performed.

57. The actuator subassembly is ready to be mounted on

the valve and the accessories attached.

Содержание FlowAct 1502













































































Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды

Flowserve FlowAct 1502, Инструкция пользователя

Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды