Flowserve FlowAct 1502 Скачать руководство пользователя страница 19

Страница: 19 / 76

FlowAct Diaphragm Linear Actuator FCD VLENIMFACTA4 10/16

flowserve.com

Item #

Part

202

6.1

Diaphragm Casing

203

6.2

Diaphragm Casing

209

6.6

Ring Nut

211

6.12

Stem

225

6.16

Diaphragm

227

6.15

Diaphragm Plate

228

6.13

Spacer Bushing

229

6.21

Actuator Spring

231

6.22

Distance Plate

253

6.8

Guide Bushing

254

6.80

Plain Bearing

255

6.18

Thrust Washer

258

6.26

Vent Plug

272

6.17

O-Ring

273

6.11

Scraper Ring

275

6.10

O-Ring

326

6.23

Spring Adjusting Plate

335

6.3.1

Hexagon Bolt - short

336

6.3.2

Hexagon Bolt - long

337

6.5

Plain Washer

339

6.25

Protection Sleeve

348

6.20

Special Nut

349

6.19

Lock Washer

351

6.4

Hexagon Nut

Table 13: Actuator parts

227

225

272

255

211

228

349

348

229

326

231

203

258

337

335

336

209

202

253

254

351

339

275

273

Figure 10: Actuator parts

uniformly in a clockwise sequence by tightening the long

hexagon bolts (336), plain washers (337) and hexagon

nuts (351). Alternative method

see NOTICE

step 5.

24. Install the short hexagon bolts (335), hexagon nuts (351)

as well as the hexagon bolts (335) and ring nuts (209).

25. Tighten the nuts (351) using a crosswise pattern in

four steps.

26. Install the protection sleeve (339).

27. Reassemble the yoke and coupling parts, perform three

full strokes then check the tightening of the casing bolting.

28. Log the maintenance interval and the work performed.

29. The actuator subassembly is ready to be mounted on

the valve and the accessories attached.

Содержание FlowAct 1502













































































Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды

Flowserve FlowAct 1502, Инструкция пользователя

Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды