manualshive.com logo in svg

Flowserve FlowAct 1502, Инструкция пользователя

Поделиться
Скачать
Flowserve FlowAct 1502 Скачать руководство пользователя страница 64

FlowAct   Diaphragm Linear Actuator      FCD VLENIMFACTA4 10/16

64

Item #

Part

WW

EU

202

6.1

Diaphragm Casing

203

6.2

Diaphragm Casing

211

6.12

Stem

220

6.14

Disk (2x)

225

6.16

Diaphragm (2x)

227

6.15

Diaphragm Plate (2x)

228

6.13

Spacer Bushing (2x)

229

6.21

Actuator Spring

231

6.22

Distance Plate (2x)

253

6.8

Lower Guide Bushing

254

6.80

Plain Bearing (2x)

255

6.18

Thrust Washer (2x)

258

6.26

Vent Plug (2x)

272

6.17

O-Ring (2x)

273

6.11

Scraper Ring

275

6.10

O-Ring (2x)

276

6.9

O-Ring (3x)

279

6.46

O-Ring (18x)

326

6.23

Spring Adjusting Plate (2x)

334

6.45

Hexagon Bolt (18x)

335

6.3.1

Hexagon Bolt - short (40x) 

1)

336

6.3.2

Hexagon Bolt - long (8x) 

1)

337

6.5

Plain Washer (48x) 

1)

339

6.25

Protection Sleeve (8x)

348

6.20

Special Nut

349

6.19

Lock Washer (2x)

351

6.4

Hexagon Nut (48x)

373

6.82

Intermediate Guide Bushing

374

6.47

Distance Bushing (2x)

380

6.81

Stem Extension

1)

   Alternatively, hex head assembled screws with captive flat washers are used for this application.

275   

231   

326   

229   

275   

273   

202   

373   

254   

   258

276   

279   

334   

211   

255   

225   

272   

220   

227   

228   

374   

349   

380   

   276

   202

   253

   254

   276

   279

   334

   339

   351

   374

   348

   334

   279

   202

   203

   258

   337

   335

   336

Table 37: Actuator parts

Figure 34: Actuator parts

44. Lubricate the new O-ring (272) with an appropriate lubricant.

45. Lower the distance bushing (374), spacer bushing 

(228), disk (220), diaphragm plate (227), 

diaphragm (225), O-ring (272), thrust 

washer (255) and lock washer (349)

onto the stem extension (380).

NOTICE

Arrange the distance bushing like an 
correctly wearing hat. The internal 

stroke stop takes over the special nut.

46. Lubricate the thread of the stem extension (380) with 

an appropriate lubricant.

NOTICE

The diaphragm plate should be posi-
tioned to the diaphragm with the aid 

of the positioning template. Mark the position.

47. Fix the stem (211) with the stem clamping tool against 

twisting.

48. Load the springs by tightening the special nut (348) 

clockwise using a suitable torque wrench, see section 

15 torque requirements.

NOTICE

We recommend you to use a hy-
draulic spring press, as a minimum 

requirement a beam and threaded rods in 8.8 quality 
(ISO 898-1) or higher as well as washers and nuts al-
ternatively.

49. Remove the stem clamping tool.

50. Install the diaphragm casing (203), positioning the 

casing such that the air connections opposites.

51. Lubricate the threats of the long hexagon bolts (336) with 

an appropriate lubricant and load the springs uniformly 

in a clockwise sequence by tightening the long hexagon 

bolts (336), plain washers (337) and hexagon nuts (351). 

52. Install the short hexagon bolts (335), plain washers (337) 

and hexagon nuts (351).

53. Tighten the nuts (351) using a crosswise pattern in 

four steps, see section 15 torque requirements.

54. Install the protection sleeve (339).

55. Perform 3 full strokes and check the tightening of the 

casing bolting.

56. Log the maintenance interval and the work performed.

57. The actuator subassembly is ready to be mounted on 

the valve and the accessories attached.

Содержание FlowAct 1502













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды