Flowserve FlowAct 1502 Скачать руководство пользователя страница 45

Страница: 45 / 76

FlowAct Diaphragm Linear Actuator FCD VLENIMFACTA4 10/16

flowserve.com

Item #

Part

202

6.1

Diaphragm Casing (2x)

209

6.6

Ring Nut

211

6.12

Stem

220

6.14

Disk

225

6.16

Diaphragm

227

6.15

Diaphragm Plate

228

6.13

Spacer Bushing

229

6.21

Actuator Spring

231

6.22

Distance Plate

253

6.8

Guide Bushing

254

6.80

Plain Bearing (2x)

255

6.18

Thrust Washer

258

6.26

Vent Plug

272

6.17

O-Ring

273

6.11

Scraper Ring (2x)

275

6.10

O-Ring (2x)

276

6.9

O-Ring (2x)

279

6.46

O-Ring (12x)

326

6.23

Spring Adjusting Plate

334

6.45

Hexagon Bolt (12x)

335

6.3.1

Hexagon Bolt - short (20x)

336

6.3.2

Hexagon Bolt - long (4x)

337

6.5

Plain Washer (24x)

339

6.25

Protection Sleeve

348

6.20

Stem

349

6.19

Lock Washer

351

6.4

Hexagon Nut (24x)

374

6.47

Distance Bushing

389

6.83

Guide Bushing

Alternatively, hex head assembled screws with captive flat washers are used for this application.

348

255

272

211

255

227

220

228

374

349

336

335

337

202

389

254

258

276

279

334

231

326

229

202

253

254

276

279

334

351

339

273

275

Table 29: Actuator parts

Figure 26: Actuator parts

with an appropriate lubricant then compress the springs

uniformly in a clockwise sequence by tightening the long

hexagon bolts (336), plain washers (337) and hexagon

nuts (351). Alternative method

see NOTICE

step 5.

24. Install the short hexagon bolts (335) and hexagon nuts

(351).

25. Tighten the nuts (351) using a crosswise pattern in

four steps.

26. Install the protection sleeve (339).

27. Reassemble the yoke and coupling parts, perform three

full strokes then check the tightening of the casing bolting.

28. Log the maintenance interval and the work performed.

29. The actuator subassembly is ready to be mounted on

the valve and the accessories attached.

Содержание FlowAct 1502













































































Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды

Flowserve FlowAct 1502, Инструкция пользователя

Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды