Flowserve FlowAct 1502 Скачать руководство пользователя страница 5

Страница: 5 / 76

FlowAct Diaphragm Linear Actuator FCD VLENIMFACTA4 10/16

flowserve.com

3. You can alternatively place a sling around the actuator

case just above the yoke.

4. Upon removing the actuator from the packaging, we

recommend that you:

• Promptly touch up any damage to the paint that of-

fers corrosion protection.

• Contact your shipper immediately to report any

damage.

• Call your Flowserve representative if you experience

any problems.

Do not remove the protective covers from the

air supply connection of the actuator or from the

instrument ports of the actuator and accessories

until the actuator is ready for installation at the site.

Figure 4: Triple-Leg Sling (Example)

Prior to installation of the actuator, we require, that you check the following conditions to reduce the risk of malfunction and

safety related incidents.

No.

Check

Possible malfunction or safety related incident

Confirm that the nominal / operational data on the

serial plate matches the operational data of the

facility.

An operational mismatch can cause considerable damage to

the actuator or may lead to a failure at the facility.

9 Installation

The actuator must be installed and commis-
sioned by qualified staff - personnel who are fa-
miliar with the installation, commissioning and
operation of this product and possess the rele-
vant qualifications in their field of activity.

Table 1: Basic safety massages for installing the actuator (continued on next page 6)

Содержание FlowAct 1502













































































Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды

Flowserve FlowAct 1502, Инструкция пользователя

Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды