manualshive.com logo in svg

Flowserve FlowAct 1502, Инструкция пользователя

Поделиться
Скачать
Flowserve FlowAct 1502 Скачать руководство пользователя страница 44

FlowAct   Diaphragm Linear Actuator      FCD VLENIMFACTA4 10/16

44

Actuator with attachments

Spring-to-close

Disassembly instruction of the actuator subas-

sembly

NOTICE

Limit disassembly only to necessary compo-
nents.

1.  Fix the actuator on the assembly table, if this is not 

already happened.

2.  Disassemble the coupling parts and yoke (see page 

54).

3.  Disassemble the hexagon bolts (335), plain washers 

(337) and hexagon nuts (351).

4.  Pull off the protection sleeve (339).

WARNING

Risk of injury by jump-
ing out parts ! Pre-loaded  

springs inside.

5.  Lubricate the threads and loosen the long hexagon bolts 

(336), plain washers (337) and hexagon nuts (351) uni-

formly in a clockwise sequence as the springs expand.

NOTICE

We recommend using threaded bolts 
meeting standards from ISO 898-1, 

8.8 or higher, as well as washers and nuts.

6.  Lift off the diaphragm casing (202 - 389), distance 

plate (231) and spring adjusting plate (326).

7.  Remove the actuator springs (229).

8.  Carefully pull out the diaphragm-stem unit (211 - 374).

9.  Remove the scraper rings (273) and O-rings (275).

10. Secure the diaphragm-stem unit into the Special Tool.

11. Loosen the stem (348) counterclockwise and remove 

the lock washer (349), distance bushing (374), spacer 

bushing (228), disk (220), diaphragm plate (227), dia-

phragm (225), O-ring (272) and thrust washer (255).

12. Check stressed surface areas for damage such as 

scoring and deformities. Use a brass brush or similar 

tool to clean bolting. Check for corrosion or any other 

damage.

Reassembly instruction of the actuator subas-

sembly

NOTICE

Always replace parts showing wear with 
new parts.

13. Lubricate the new O-rings (275), new scraper rings 

(273) with an appropriate lubricant and install into the 

guide bushings (253).

 

14. Lubricate the new O-ring (272) with an appropriate 

lubricant.

15. Lower the thrust washer (255), O-ring (272), dia-

phragm (225), diaphragm plate (227), 

disk (220), spacer bushing (228), distance 

bushing (374) and lock washer (349)

onto the stem (211).

16. Lubricate the thread of the stem (211) with an appropri-

ate lubricant and install and finger tighten the stem (348).

NOTICE

The diaphragm plate should be posi-
tioned to the diaphragm with the aid 

of the Positioning Template. Mark the position.

17. Turn clockwise the stem (348) using a suitable torque 

wrench.

18. Loosen and remove the diaphragm-stem unit (211- 

374) from the Special Tool. Lubricate the actuator 

stem with an appropriate lubricant.

19. Carefully lower the diaphragm-stem unit (211- 374) 

into the diaphragm casing.

NOTICE

Position the diaphragm-stem unit 
such that the air connection and the 

Mark align.

20. Install and align the actuator springs (229).

21. Install and position the spring adjusting plate (326) 

such that the imprint on the plate and air connection 

are opposite of each other.

22. Install the distance plate (231) and diaphragm casing 

(203), position the casing allowing the air connections 

to be opposite of each other.

23. Lubricate the threats of the long hexagon bolts (336) 

Содержание FlowAct 1502













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды