manualshive.com logo in svg

Flowserve FlowAct 1502, Инструкция пользователя

Поделиться
Скачать
Flowserve FlowAct 1502 Скачать руководство пользователя страница 20

FlowAct   Diaphragm Linear Actuator      FCD VLENIMFACTA4 10/16

20

Actuator without attachments

Spring-to-open

Disassembly instruction of the actuator subas-

sembly

NOTICE

Limit disassembly only to necessary compo-
nents.

1.  Fix the actuator on the assembly table, if this is not 

already happened.

2.  Loosen the lock nut (344) counterclockwise and disas-

semble the upper coupling (249) and lock nut clock-

wise (see page 15).

3.  Disassemble the hexagon bolts (335), plain washers 

(337), hexagon nuts (351) and ring nuts (209).

4.  Pull off the protection sleeve (339).

WARNING

Risk of injury by jump-
ing out parts ! Pre-loaded  

springs inside.

5.  Lubricate the threads and loosen the long hexagon bolts 

(336), plain washers (337) and hexagon nuts (351) uni-

formly in a clockwise sequence as the springs expand.

NOTICE

We recommend using threaded bolts 
meeting standards from ISO 898-1, 

8.8 or higher, as well as washers and nuts.

6.  Lift off the diaphragm casing (203).

7.  Carefully remove the diaphragm-stem unit (211 - 349).

8.  Remove the actuator springs (229).

9.  Remove the spring adjusting plate (326).

10. Remove the scraper ring (273) and O-ring (275).

11. Secure the diaphragm-stem unit into the Special Tool.

12. Loosen the special nut (348) counterclockwise and 

remove the lock washer (349), thrust washer (255), O-

ring (272), diaphragm (225), diaphragm plate (227), 

and spacer bushing (228).

13. Check stressed surface areas for damage such as 

scoring and deformities. Use a brass brush or similar 

tool to clean bolting. Check for corrosion or any other 

damage.

Reassembly instruction of the actuator subas-

sembly

NOTICE

Always replace parts showing wear with 
new parts.

14. Lubricate the new O-ring (275), new scraper ring (273) 

with an appropriate lubricant and install into the guide 

bushing (253).

 

15. Lubricate the new O-ring (272) with an appropriate 

lubricant.

16. Lower the spacer bushing (228), diaphragm plate 

(227), diaphragm (225), O-ring (272), 

thrust washer (255), lock washer (349)

onto the stem (211).

17. Lubricate the thread of the stem (211) with an appro-

priate lubricant and install and finger tighten the spe-

cial nut (348).

18. Turn the special nut (348) clockwise using a suitable 

torque wrench.

19. Loosen and remove the diaphragm-stem unit (211- 

349) from the Special Tool. Lubricate the actuator 

stem with an appropriate lubricant.

20. Install and positioning the spring adjusting plate (326) 

such that the drilling and air connection match.

21. Install and align the actuator springs (229).

22. Carefully lower the diaphragm-stem unit (211- 349) 

into the diaphragm casing.

23. Install the diaphragm casing (203), positioning the 

casing such that the air connections are aligned.

24. Lubricate the threats of the long hexagon bolts (336) 

with an appropriate lubricant then compress the springs 

uniformly in a clockwise sequence by tightening the long 

hexagon bolts (336), plain washers (337) and hexagon 

nuts (351). Alternative method

 see NOTICE

 step 5.

25. Install the short hexagon bolts (335), hexagon nuts (351) 

as well as the hexagon bolts (335) and ring nuts (209).

26. Tighten the nuts (351) using a crosswise pattern in 

four steps.

Содержание FlowAct 1502













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды