manualshive.com logo in svg

Flowserve FlowAct 1502, Инструкция пользователя

Поделиться
Скачать
Flowserve FlowAct 1502 Скачать руководство пользователя страница 18

FlowAct   Diaphragm Linear Actuator      FCD VLENIMFACTA4 10/16

18

Actuator without attachments

Spring-to-close

Disassembly instruction of the actuator subas-

sembly

NOTICE

Limit disassembly only to necessary compo-
nents.

1.  Fix the actuator on the assembly table, if this is not 

already happened.

2.  Loosen the lock nut (344) counterclockwise and disas-

semble the upper coupling (249) and lock nut clock-

wise (see page 15).

3.  Disassemble the short hexagon bolts (335), plain wash-

ers (337), hexagon nuts (351) and ring nuts (209).

4.  Pull off the protection sleeve (339).

WARNING

Risk of injury by jump-
ing out parts ! Pre-loaded  

springs inside.

5.  Lubricate the threads and loosen the long hexagon bolts 

(336), plain washers (337) and hexagon nuts (351) uni-

formly in a clockwise sequence as the springs expand.

NOTICE

We recommend using threaded bolts 
meeting standards from ISO 898-1, 

8.8 or higher, as well as washers and nuts.

6.  Lift off the diaphragm casing (203), distance plate 

(231) and spring adjusting plate (326).

7.  Remove the actuator springs (229).

8.  Carefully remove the diaphragm-stem unit (211 - 349).

9.  Remove the scraper ring (273) and O-ring (275).

10. Secure the diaphragm-stem unit into the Special Tool.

11. Loosen the special nut (348) counterclockwise and 

remove the lock washer (349), spacer bushing (228), 

diaphragm plate (227), diaphragm (225), O-ring (272) 

and thrust washer (255).

12. Check stressed surface areas for damage such as scor-

ing and deformities. Use a brass brush or similar tool to 

clean bolting. Check for corrosion or any other damage.

Reassembly instruction of the actuator subas-

sembly

NOTICE

Always replace parts showing wear with 
new parts.

13. Lubricate the new O-ring (275), new scraper ring (273) 

with an appropriate lubricant and install into the guide 

bushing (253).

 

14. Lubricate the new O-ring (272) with an appropriate 

lubricant.

15. Lower the thrust washer (255), diaphragm (225), O-

ring (272), diaphragm plate (227), spacer 

bushing (228), lock washer (349)

onto the stem (211).

16. Lubricate the thread of the stem (211) with an appro-

priate lubricant and install and finger tighten the spe-

cial nut (348).

NOTICE

The diaphragm plate should be posi-
tioned to the diaphragm with the aid 

of the Positioning Template. Mark the position.

17. Turn the special nut (348) clockwise using a suitable 

torque wrench.

18. Loosen and remove the diaphragm-stem unit (211- 

349) from the Special Tool. Lubricate the actuator 

stem with an appropriate lubricant.

19. Carefully lower the diaphragm-stem unit (211- 349) 

into the diaphragm casing.

NOTICE

Position the diaphragm-stem unit 
such that the air connection and the 

Mark align.

20. Install and align the actuator springs (229).

21. Install and positioning the spring adjusting plate (326) 

such that the drilling, mark and air connection match.

22. Install the distance plate (231) and diaphragm casing 

(203), positioning the casing such that the drilling, 

mark and air connections match.

23. Lubricate the threats of the long hexagon bolts (336) 

with an appropriate lubricant then compress the springs 

Содержание FlowAct 1502













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды