Flowserve FlowAct 1502 Скачать руководство пользователя страница 23

Страница: 23 / 76

FlowAct Diaphragm Linear Actuator FCD VLENIMFACTA4 10/16

flowserve.com

Item #

Part

202

6.1

Diaphragm Casing

203

6.2

Diaphragm Casing

209

6.6

Ring Nut

211

6.12

Stem

225

6.16

Diaphragm

227

6.15

Diaphragm Plate

228

6.13

Spacer Bushing

229

6.21

Actuator Spring

231

6.22

Distance Plate

253

6.8

Guide Bushing

254

6.80

Plain Bearing (2x)

255

6.18

Thrust Washer

258

6.26

Vent Plug

272

6.17

O-Ring

273

6.11

Scraper Ring (2x)

275

6.10

O-Ring (2x)

276

6.9

O-Ring

326

6.23

Spring Adjusting Plate

335

6.3.1

Hexagon Bolt - short

336

6.3.2

Hexagon Bolt - long

337

6.5

Plain Washer

339

6.25

Protection Sleeve

348

6.29

Stem

349

6.19

Lock Washer

351

6.4

Hexagon Nut

390

6.24

Guide Bushing

Table 15: Actuator parts

336

335

337

202

276

390

254

258

326

229

273

275

339

351

202

253

254

211

255

272

225

227

228

349

348

209

276

Figure 12: Actuator parts

25. Install the short hexagon bolts (335), hexagon nuts (351)

as well as the hexagon bolts (335) and ring nuts (209).

26. Tighten the nuts (351) using a crosswise pattern in

four steps.

27. Install the protection sleeve (339).

28. Reassemble the yoke and coupling parts, perform three

full strokes then check the tightening of the casing bolting.

29. Log the maintenance interval and the work performed.

30. The actuator subassembly is ready for the reassemble

of the attachments - see page 16 - and accessories.

Содержание FlowAct 1502













































































Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды

Flowserve FlowAct 1502, Инструкция пользователя

Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды