manualshive.com logo in svg

Flowserve FlowAct 1502, Инструкция пользователя

Поделиться
Скачать
Flowserve FlowAct 1502 Скачать руководство пользователя страница 22

FlowAct   Diaphragm Linear Actuator      FCD VLENIMFACTA4 10/16

22

Actuator with attachments

Spring-to-close

Disassembly instruction of the actuator subas-

sembly

NOTICE

Limit disassembly only to necessary compo-
nents.

1.  Fix the actuator on the assembly table, if this is not 

already happened.

2.  Disassemble the attachments first (see page 16).

3.  Loosen the lock nut (344) clockwise and disassemble 

the upper coupling (249) and lock nut (see page 15).

4.  Disassemble the hexagon bolts (335), plain washers 

(337), hexagon nuts (351) and ring nuts (209).

5.  Pull off the protection sleeve (339).

WARNING

Risk of injury by jump-
ing out parts ! Pre-loaded  

springs inside.

6.  Lubricate the threads and loosen the long hexagon bolts 

(336), plain washers (337) and hexagon nuts (351) uni-

formly in a clockwise sequence as the springs expand.

NOTICE

We recommend using threaded bolts 
meeting standards from ISO 898-1, 

8.8 or higher, as well as washers and nuts.

7.  Lift off the diaphragm casing (203) and spring adjust-

ing plate (326).

8.  Remove the actuator springs (229).

9.  Carefully remove the diaphragm-stem unit (211 - 349).

10. Remove the scraper rings (273) and O-rings (275).

11. Secure the diaphragm-stem unit into the Special Tool.

12. Loosen the special stem (348) counterclockwise and 

remove the lock washer (349), spacer bushing (228), 

diaphragm plate (227), diaphragm (225), O-ring (272) 

and thrust washer (255).

13. Check stressed surface areas for damage such as scoring 

and deformities. Use a brass brush or similar tool to clean 

bolting. Check for corrosion or any other damage.

Reassembly instruction of the actuator subas-

sembly

NOTICE

Always replace parts showing wear with 
new parts.

14. Lubricate the new O-rings (275), new scraper rings 

(273) with an appropriate lubricant and install into the 

guide bushing (253 and 390).

 

15. Lubricate the new O-ring (272) with an appropriate lubricant.

16. Lower the thrust washer (255), diaphragm (225), O-

ring (272), diaphragm plate (227), spacer 

bushing (228), lock washer (349)

onto the stem (211).

17. Lubricate the thread of the stem (211) with an appropriate lu-

bricant and install and finger tighten the special stem (348).

NOTICE

The diaphragm plate should be posi-
tioned to the diaphragm with the aid 

of the Positioning Template. Mark the position.

18. Turn clockwise the special stem (348) using a suitable 

torque wrench.

19. Loosen and remove the diaphragm-stem unit (211 

- 349) from the Special Tool. Lubricate the actuator 

stems with an appropriate lubricant.

20. Carefully lower the diaphragm-stem unit (211 - 349) 

into the diaphragm casing.

NOTICE

Position the diaphragm-stem unit 
such that the air connection and the 

Mark align.

21. Install and align the actuator springs (229).

22. Install and positioning the spring adjusting plate (326) 

such that the drilling, mark and air connection match.

23. Install the diaphragm casing (203), positioning the casing 

such that the drilling, mark and air connections match.

24. Lubricate the threats of the long hexagon bolts (336) 

with an appropriate lubricant and load the springs uni-

formly in a clockwise sequence by tightening the long 

hexagon bolts (336), plain washers (337) and hexagon 

nuts (351). Alternative method see 

NOTICE

 step 6.

Содержание FlowAct 1502













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды