manualshive.com logo in svg

Flowserve FlowAct 1502, Инструкция пользователя

Поделиться
Скачать
Flowserve FlowAct 1502 Скачать руководство пользователя страница 67

FlowAct   Diaphragm Linear Actuator      FCD VLENIMFACTA4 10/16

67

flowserve.com

NOTICE

Always replace parts showing wear with 
new parts.

22. Lubricate the new O-ring (275) and new scraper ring 

(273) with an appropriate lubricant and install into the 

guide bushing (253).

23. Lubricate the new O-ring (275) with an appropriate lu-

bricant and install into the guide bushing (6.82).

24. Fix the stem (211) into the stem clamping tool.

25. Lubricate the new O-ring (272) with an appropriate 

lubricant.

26. Lower the thrust washer (255), O-ring (272), dia-

phragm (225), diaphragm plate (227), 

disk (220), spacer bushing (228), distance 

bushing (374) and lock washer (349)

onto the stem (211).

NOTICE

Arrange the distance bushing like an 
upside down top hat. Its function is 

that of an internal stroke stop.

27. Lubricate the thread of the stem (211) with an appro-

priate lubricant and install and finger tighten the stem 

extension (380).

NOTICE

The diaphragm plate should be posi-
tioned to the diaphragm with the aid 

of the positioning template. Mark the position.

28. Turn clockwise the stem extension (380) using a suit-

able torque wrench, see section 15 torque requirements.

29. Loosen and remove the diaphragm-stem unit (211 - 

380) out of the stem clamping tool. Lubricate the ac-

tuator stem with an appropriate lubricant.

30. Carefully lower the diaphragm-stem unit (211 - 380) 

into the diaphragm casing (202 - 373).

NOTICE

Position the diaphragm-stem unit 
such that the air connection and the 

Mark align.

31. Install and align the actuator springs (229).

NOTICE

The surface, respectively the edges 
of the spring ends should be aligned 

to the actuators center. If these will ignored the spring 
may touch the actuators casing and rub in rare cases.

32. Install and position the spring adjusting plate (326) 

such that the imprint on the plate and air connection 

are opposite of each other.

33. Install the distance plate (231) and diaphragm casing 

(202 - 389), positioning the casing such that the air 

connections opposites.

34. Lubricate the threats of the long hexagon bolts (336) 

with an appropriate lubricant and load the springs uni-

formly in a clockwise sequence by tightening the long 

hexagon bolts (336), plain washers (337) and hexagon 

nuts (351). Alternative method see 

NOTICE

 step 4.

35. Install the short hexagon bolts (335), plain washers (337) 

and hexagon nuts (351).

36. Tighten the nuts (351) using a crosswise pattern in 

four steps, see section 15 torque requirements.

37. Install the protection sleeve (339).

38. Assemble the coupling parts (see page 54).

39. Lubricate the new O-ring (276) with an appropriate 

lubricant and install it onto the guide bushing (373).

40. Lubricate the threats of the hexagon bolts (334) and 

the new O-rings (279) with an appropriate lubricant 

and install it onto the guide bushing (373). Tighten the 

bolts (334) using a crosswise pattern in two steps, see 

section 15 torque requirements.

41. Lubricate the new O-ring (272) with an appropriate lubricant.

42. Lower the thrust washer (255), O-ring (272), dia-

phragm (225), diaphragm plate (227), 

disk (220), spacer bushing (228), dis-

tance bushing (374) and lock washer

onto the stem (211).

NOTICE

Arrange the distance bushing like an 
correctly wearing hat. The internal 

stroke stop takes over the special nut.

Содержание FlowAct 1502













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды