Flowserve FlowAct 1502 Скачать руководство пользователя страница 68

Страница: 68 / 76

FlowAct Diaphragm Linear Actuator FCD VLENIMFACTA4 10/16

Item #

Part

202

6.1

Diaphragm Casing (4x)

211

6.12

Stem

220

6.14

Disk (2x)

225

6.16

Diaphragm (2x)

227

6.15

Diaphragm Plate (2x)

228

6.13

Spacer Bushing (2x)

229

6.21

Actuator Spring

231

6.22

Distance Plate (2x)

253

6.8

Lower Guide Bushing

254

6.80

Plain Bearing (3x)

255

6.18

Thrust Washer (2x)

258

6.26

Vent Plug (2x)

272

6.17

O-Ring (2x)

273

6.11

Scraper Ring (2x)

275

6.10

O-Ring (3x)

276

6.9

O-Ring (4x)

279

6.46

O-Ring (24x)

326

6.23

Spring Adjusting Plate (2x)

334

6.45

Hexagon Bolt (24x)

335

6.3.1

Hexagon Bolt - short (40x)

336

6.3.2

Hexagon Bolt - long (8x)

337

6.5

Plain Washer (48x)

339

6.25

Protection Sleeve (8x)

348

6.20

Stem

349

6.19

Lock Washer (2x)

351

6.4

Hexagon Nut (48x)

373

6.82

Intermediate Guide Bushing

374

6.47

Distance Bushing (2x)

380

6.81

Stem Extension

389

6.83

Upper Guide Bushing

Alternatively, hex head assembled screws with captive flat washers are used for this application.

275

231

326

229

275

273

202

373

254

258

276

279

334

211

255

225

272

220

227

228

374

349

380

202

253

254

276

279

334

339

351

374

348

334

279

276

202

389

254

276

279

334

258

337

335

336

Table 38: Actuator parts

Figure 35: Actuator parts

43. Lubricate the thread of the stem extension (380) with

an appropriate lubricant and install and finger tighten

the stem (348).

NOTICE

The diaphragm plate should be posi-
tioned to the diaphragm with the aid

of the positioning template. Mark the position.

44. Fix the stem (211) with the stem clamping tool against

twisting.

45. Turn clockwise the stem (348) using a suitable torque

wrench, see section 15 torque requirements.

46. Remove the stem clamping tool.

47. Install and align the actuator springs (229).

NOTICE

The surface, respectively the edges
of the spring ends should be aligned

to the actuators center. If these will ignored the spring
may touch the actuators casing and rub in rare cases.

48. Install and position the spring adjusting plate (326)

such that the imprint on the plate and air connection

are opposite of each other.

49. Install the distance plate (231) and diaphragm casing

(203), positioning the casing such that the air connec-

tions opposites.

50. Lubricate the threats of the long hexagon bolts (336)

with an appropriate lubricant and load the springs uni-

formly in a clockwise sequence by tightening the long

hexagon bolts (336), plain washers (337) and hexagon

nuts (351). Alternative method see

NOTICE

step 4.

51. Install the short hexagon bolts (335), plain washers (337)

and hexagon nuts (351).

52. Tighten the nuts (351) using a crosswise pattern in

four steps, see section 15 torque requirements.

53. Install the protection sleeve (339).

54. Perform 3 full strokes and check the tightening of the

casing bolting.

55. Log the maintenance interval and the work performed.

56. The actuator subassembly is ready to be mounted on

the valve and the accessories attached.

Содержание FlowAct 1502













































































Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды

Flowserve FlowAct 1502, Инструкция пользователя

Результаты поиска

Содержание FlowAct 1502

Отзывы:

Бренды по названию

Популярные бренды