Fischer Panda AGT 6000 PVMV-N Скачать руководство пользователя | Manualshive

Страница: 89 / 132

background image

Generator Failure

AGT 6000 PVMV-N 12V_24V - Chapter D: Generator Failure Page 87

D.3 Starting Problems

D.3.1 Fuel Solenoid Valve and Hubmagnet

For start problems the possibility of an error exists with the solenoid for engine stop or fuel sole-
noid valve, which both effect affect simultaneous on the fuel system.

1. Fuel solenoid valve

The fuel solenoid valve is located in front of the injection pump. It opens automatically, if the
"START"-button is pressed on the remote control panel. The solenoid valve is CLOSED when the
generator main power is switched "OFF". For this reason, it requires a few seconds before the
motor comes to a full halt

If the generator fails to start, runs rough, does not reach the proper RPM, or does not stop pro-
perly, the first item to suspect in most cases is the fuel solenoid valve and should be inspected
first.

A check of the fuel solenoid valve by removing the plug from the fuel solenoid valve for a short
period whilst in operation (first remove the small retention screw) and replace it immediately. The
motor should "react immediately" by revving high.If the motor does not react sharply to the recon-
nection of the solenoid wire, it is a sign that the solenoid valve could be faulty.

2. Solenoid for engine stop

The solenoid for engine stop is located at the injection pump.

1. Energized to stop

By pressing the "OFF"-button on the remote control panel, the solenoid is supplied with voltage
and attracts, whereby the fuel injection pump resets to the zero position and the generator stops.

2. Energized to run

This version is equipped with two solenoids an actuating and a stop solenoid. After being fed with
current, the actuating solenoid attracts the adjusting lever of the fuel injection pump, through
which the fuel can flow. The actuating solenoid is switched parallel to the starter motor, the stop
solenoid is switched parallel to the fuel pump. The position is held by the stop solenoid as long as
the generator is running.

01. Fuel solenoid valve

02. Fuel injector nozzles

03. Ventilation screw

Fig. D.3.1-1: Fuel solonoid valve

01

02

03

«
...
87
88
89
90
91
...
»

Содержание AGT 6000 PVMV-N





































































































































Отзывы:

Нет отзывов

Похожие инструкции для AGT 6000 PVMV-N

Бренд: Teac Страницы: 6

Бренд: Generac Power Systems Страницы: 36

StreetParty III

Бренд: Gear4 Страницы: 9

VOYAGER VPS 26/10-B

Бренд: AVION Страницы: 12

EUROPORT MPA200BT

Бренд: Behringer Страницы: 40

Бренд: Radio Shack Страницы: 4

Бренд: Daewoo Страницы: 91

Бренд: Thames & Kosmos Страницы: 20

DIGITRADIO 230 OD

Бренд: TechniSat Страницы: 644

Бренд: Wanroy Страницы: 6

Бренд: Landa Страницы: 30

Бренд: Curtis Страницы: 1

Бренд: Hyundai Страницы: 45

Бренд: Queen Bee Power Страницы: 1

Бренд: Tahoe Страницы: 34

Бренд: Workzone Страницы: 22

Бренд: Magnavox Страницы: 2

Бренд: H3C Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды