Fischer Panda AGT 6000 PVMV-N Скачать руководство пользователя | Manualshive

Страница: 120 / 132

background image

Remote Control Panda 6-50

Seite/Page 118 - Kapitel/Chapter A: Remote Control Panda 6-50

F1WT1-95E730 Panda 6-50 Fernbedienpanel_eng.fm

Fischer Panda Datasheet

A.1 Cleaning and replacement of parts at the generator

The battery must always be disconnected, if work on the generator or electrical system is
to be carried out, so that the generator cannot be unintentionally started.

Note the safety instruction in the generator manual.

The raw water valve must be shut (marine version).

Attention!!! Parts of the generator and the cooling water may be hot after operation
!!!DANGER!!!

A.2 General information

The Panda generator is supplied with an external remote control panel. The remote control panel is necessary to
control the generator and to evaluate the motor/generator properties. Generator control includes, on switch, pre-
heat, starting and stopping generator functions.

The remote control panel is equipped with some new monitoring functions, which increase the operational safety
of the generator. A failure message is shown over contacts which are normally closed. If a connection is intermit-
ted, a failure message is triggered.

The generator may not be run without the remote control panel.

Fig. A.2-1: Remote Control Panel

01

02

03

04

05

08

09

10

11

15

12

13

14

06

07

01. Warning light for cooling water temperature
02. Warning light for water leak (sensor optional)
03. Warning light for AC fault (optional)
04. AC voltage control light
05. Warning light for winding temperature
06. Warning light for oil pressure
07. Battery charge voltage 12 V - DC control lamp
08. LED display for pre-glow

09. Pre-glow button (Heat)
10. Generator „START“-button
11. Control light for Generator-Start
12. Generator „Off“ button
13. Generator „On“ button
14. Generator „stand by“ control light
15. Running hours counter

«
...
118
119
120
121
122
...
»

Содержание AGT 6000 PVMV-N





































































































































Отзывы:

Нет отзывов

Похожие инструкции для AGT 6000 PVMV-N

Бренд: Cross Tools Страницы: 68

Бренд: Goodmans Страницы: 2

Nite Lite V Series

Бренд: Allmand Страницы: 17

Бренд: Extron electronics Страницы: 32

Бренд: Milwaukee Страницы: 19

Бренд: Briggs & Stratton Страницы: 8

Бренд: LENCO Страницы: 68

Бренд: Sangean Страницы: 14

Бренд: Rockpals Страницы: 16

Бренд: Whisper Power Страницы: 32

Бренд: Harman Страницы: 20

Бренд: Huawei Страницы: 68

Бренд: Huawei Страницы: 307

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 44

Бренд: Sony Страницы: 46

Бренд: Klein Tools Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды