Fischer Panda AGT 6000 PVMV-N Скачать руководство пользователя

Страница: 14 / 132

Measures to the fire protection.

All construction units in the environment of energized parts, which carry more than 50 Amp., must be fire protection-
moderately secured.

All junction points at the energized parts must be examined regularly on heating up (infrared thermometers).

Safety Instrictions for the Handling with Batteries

These instructions must be noticed additionally to the instructions of the battery manufacturer:

• If the batteries are working, someone should be in your near area to help you in a case of emergency.

• Water and soap must be hold ready if battery acid corrode your skin.

• Wear eye protection and protective clothing. During working with the batteries don´t touch the eyes.

• If you got a acid splash on your skin or clothing grow it with much water and soap out.

• If you got acid in your eyes rinse them immediately with clear water until no cauterization is noticeable. Visit imme-

diate a doctor.

• Don´t smoke in the near of the batteries. Avoid naked flames or open fires. In the area of batteries exists danger

of explosions.

• Pay attention that no tools fall on the battery poles, if necessary cover them.

• During the installation don´t wear a wrist watch or arm jewels, you can create under these circumstances a battery

short-circuit. Burning of the skin could be the result.

• Protect every battery contact against unintentional touch.

• Use only cyclical profoundly dischargeable batteries. Starter batteries are not appropriate. Lead-gel batteries are

commended. They are maintenance-free, profoundly dischargeable and not produce gas.

• Do not charge a frozen battery.

• Avoid a batterie short-curcuit.

• Take care of a good ventilation of the battery to drain off developing gas.

• The battery connection terminals must be checked of a tight contact at least before operating.

• The battery connection cable must be carefully mounted and checked about incorrect heating at operation with

load. The vibrating devices must be regulary checked about scour points and flaw in the isolation.

Содержание AGT 6000 PVMV-N





































































































































Результаты поиска

Содержание AGT 6000 PVMV-N

Отзывы:

Похожие инструкции для AGT 6000 PVMV-N

Бренды по названию

Популярные бренды

Fischer Panda AGT 6000 PVMV-N, Руководство пользователя

Результаты поиска

Содержание AGT 6000 PVMV-N

Отзывы:

Похожие инструкции для AGT 6000 PVMV-N

Бренды по названию

Популярные бренды