Fischer Panda AGT 6000 PVMV-N Скачать руководство пользователя | Manualshive

Страница: 11 / 132

background image

9

CALIFORNIA

Proposition 65 Warning

Diesel engine exhaust and some of its constituents

are known to the State of California to cause cancer,

birth defects, and other reproductive harm.

Attention, Important Directions regarding Operation!

1. The installation certificate must be completed when taken into use, and certified by a signature.

2. The installation certificate must be despatched within two weeks of use to Fischer Panda.

3. The official guaranty confirmation will be completed by Fischer Panda after receipt and sent to the customer.

4. A guaranty must be shown to make any claims.

Claims against the guaranty will not be accepted of the above said instructions are not, or only partially, carried out.

Manufacturer declaration in terms of the machine guideline 98/37/EG .

The generator is in such a way developed that all assembly groups correspond to the CE guidelines. If machine gui-
deline 98/37/EG is applicable, then it is forbidden to bring the generator into operation until it has been determined
that the system into which the generator is to be installed in also corresponds to the regulations of the machine gui-
deline 98/37/EG. This concerns among other things the exhaust system, cooling system and the electrical installa-
tion.

The evaluation of the "protection against contact" can only be accomplished in connection with the respective
system. Likewise among other things responsibility for correct electrical connections, a safe ground wire connection,
foreign body and humidity protection, protection against humidity due to excessive condensation as well as the over-
heating through appropriate and inappropriate use in its installed state on the respective machine lies within the
responsibility of those who undertake installation of the generator in the system.

Use the advantages of the customer registration:

• Thus you receive to extended product informations, which are sometimes safety-relevant

• you receive, if necessarily free Upgrades

Far advantages:

By your full information Fischer Panda technicians can give you fast assistance, since 90% of the disturbances result
from errors in the periphery.

Problems due to errors in the installation can be recognized in the apron.

Technical Support per Internet: [email protected]

«
...
9
10
11
12
13
...
»

Содержание AGT 6000 PVMV-N





































































































































Отзывы:

Нет отзывов

Похожие инструкции для AGT 6000 PVMV-N

Бренд: Samsung Страницы: 32

Бренд: Samsung Страницы: 32

Black Max PMC435250

Бренд: Powermate Страницы: 16

Бренд: Mase Generators Страницы: 92

Бренд: Paso Страницы: 30

Бренд: MayPole Страницы: 2

Бренд: Generac Power Systems Страницы: 56

PD60 UL913 Series

Бренд: Hytera Страницы: 37

Бренд: Vertex Standard Страницы: 34

Studiophile SP-8S

Бренд: M-Audio Страницы: 15

Бренд: Firman Страницы: 39

Бренд: Wacker Neuson Страницы: 38

Бренд: Winco Страницы: 32

OTC AC/MIG/201 CPDACA-200

Бренд: Daihen Страницы: 48

Бренд: Landa Страницы: 30

Бренд: Feider Machines Страницы: 80

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды