FHF ExResistTel IP2/IP154 Скачать руководство пользователя страница 345 | Manualshive

Страница: 345 / 412

background image

Manual ResistTel IP2 / IP152

Page 345

ExResistTel IP2 / IP154

Code

Name

Description

0x00110052 Network: UDP

checksum

UDP checksum

0x00110053 Network: UDP bind

error

Local error.

UDP socket was trying to bind itself to a
specific local port number.

The port number was found to be in use by
some other socket.

0x0011005a Network Route Error:

no route

No route

0x0011005b Network Route Error:

No route through
interface (Interface
down)

The IP routing process failed to deliver a
packet explicitly directed to a specific
network interface. The network interface
was either down or disabled. Packets
directed to a specific network interface are
used for example by DHCP (UDP) and by
PPTP Tunnels (TCP/GRE).

If this error is reported for UDP broadcast
packets rather often it usually indicates that
DHCP client mode is configured for the
interface but the interface is not connected
to a network or disabled. In this case the
DHCP mode should be changed to disabled.

0x0011005c Network Route Error:

Interface unconfigured

Interface not configured

0x0011005d Network Route Error:

Interface no gateway

Interface is no gateway

«
...
343
344
345
346
347
...
»

Содержание ExResistTel IP2/IP154





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExResistTel IP2/IP154

Бренд: Audiovox Страницы: 79

Бренд: Neoi Страницы: 50

Бренд: Audiovox Страницы: 18

Бренд: M4 Страницы: 19

Бренд: OPlus Страницы: 35

Бренд: Avaya Страницы: 32

Telenium IP IP7008D

Бренд: Vodavi Страницы: 2

SPH-A580 Series

Бренд: Samsung Страницы: 156

Бренд: Samsung Страницы: 156

Бренд: Samsung Страницы: 153

Бренд: Samsung Страницы: 156

Бренд: Samsung Страницы: 72

Бренд: Xiaomi Страницы: 52

Бренд: Zonda Страницы: 21

Бренд: Sanyo Страницы: 2

Бренд: Honeywell Страницы: 9

Бренд: Honeywell Страницы: 2

Бренд: Philips Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды