FHF ExResistTel IP2/IP154 Скачать руководство пользователя страница 214

Страница: 214 / 412

Page 214

Manual

ResistTel IP2 / IP152

ExResistTel IP2 / IP154

40Bit: Key length 40 bits for data encryption.

128Bit: Key length 128 bits for data encryption.

Descriptive name

The name of the interface

Bandwidth (kBit/s)

Limits the transfer speed of the connection (PPTP and
PPPOE) to the value to be entered here.

Maximum transfer
unit (Bytes)

Here, the maximum size of the IP packet is limited. The
default MTU values are:

•

PPPoE - 1492

•

PPTP – 1436

IP address for
remote party

If the distant end does not assign an IP address, here you
may define your own IP address in the remote IP net.

Automatic dial after
boot

Immediately after booting, attempts are made to establish
the connection.

Restart Time
(hour:min)

Time of day when the connection should be restarted to
overcome the 24-hour provider disconnect

Allow inbound
connections

Allows requests for inbound connections from the remote IP
net.

No DNS on this
interface

DNS server configurations are ignored.

Exclude interface
from NAT

The Network Translation is executed as long as this IP
address does not appear.

Содержание ExResistTel IP2/IP154





























































































































































































































































































































































































































Результаты поиска

Содержание ExResistTel IP2/IP154

Отзывы:

Похожие инструкции для ExResistTel IP2/IP154

Бренды по названию

Популярные бренды

FHF ExResistTel IP2/IP154, Руководство по эксплуатации

Результаты поиска

Содержание ExResistTel IP2/IP154

Отзывы:

Похожие инструкции для ExResistTel IP2/IP154

Бренды по названию

Популярные бренды