Eliet Turfaway 600 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 88

background image

75

English

11.6. Maintenance after every 200 hours of operation

11.6.1. Change the air filter

Despite regularly cleaning the air filter, this is still affected by wear and embedded dirt over
time. Microscopic tears or dirt penetrating deep inside the filter tissue can be hard to see with
the naked eye. Even so, they will affect the operation of the engine or cause wear and tear. It is
therefore important to replace the air filter as a preventive measure after a certain time.

New filter cartridges can be ordered from your ELIET dealer or a service centre authorised by
the engine manufacturer. The order code for the cartridge filter is:

• paper: Honda 17210-ZE1 - 822
• sponge: Honda 17218-ZE1 - 821

To replace it, follow the same procedure as described in § 11.4.4.

11.6.2. Check and/or change the spark plug

ELIET recommends the following spark plugs:

Honda GX 200 - 6.5 HP

BPR 6 ES (NGK)

• Turn off the engine and pull the cable from the spark plug.
• Clean the area around the spark plug and remove the spark plug

from the cylinder head.

• Using a feeler gauge, check whether the distance between the

electrodes is 0.8 mm.

• The spark plug must be replaced if it shows heavy deposits or is

very dirty.

• Take the following steps to verify ignition quality:

• Put the spark plug cap back on.
• Grab the rubber of the spark plug cap and press the outermost electrode against the mass of

the engine.

• Pull the starter rope.
• Check for sparks between the electrodes.
• The spark plug is in good condition if the sparks are clear and neatly centred between the

electrodes.

• Weak, irregular and off-centre sparks between the electrodes indicate that the spark plug

must be changed.

Caution:

Fitting or changing a spark plug must be done with utmost caution so

as not to damage the screw thread in the engine. Secure the spark plug with a
torque of 20 Nm.

For your information:

The above description is for indication purposes. You

must also read the manual provided by the engine manufacturer.

0,8 mm

«
...
73
74
75
76
77
...
»

Содержание Turfaway 600

























































































Отзывы:

Нет отзывов

Похожие инструкции для Turfaway 600

Бренд: MacDon Страницы: 17

Бренд: Kellfri Страницы: 12

Бренд: Metrohm Страницы: 42

Бренд: Proceq Страницы: 35

Orbit Marine IC PRO LED

Бренд: Current Страницы: 12

Бренд: KaVo Страницы: 68

Бренд: A&D Страницы: 22

Бренд: Emos Страницы: 16

Бренд: Radarcan Страницы: 40

Lighting Systems LP-10

Бренд: Lightolier Страницы: 2

Бренд: S&P Страницы: 4

Бренд: HQ Power Страницы: 9

Advanced Melting Point Apparatus

Бренд: VWR Страницы: 17

Бренд: Kellfri Страницы: 32

Veilleuse Tweesty

Бренд: babymoov Страницы: 4

Бренд: Fluke Страницы: 36

Бренд: Kellfri Страницы: 16

Бренд: Encore Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды