Eelectron BO08A01KNX Скачать руководство пользователя

Страница: 49 / 51

BO08A01KNXFI01010002.DOC

Din Rail 8 Output Module– Product Handbook

49/51

Eelectron SpA, Via Magenta 77/22, I-20017 Rho (MI), Italia
+39 02.9316681 +39 02.93507688
[email protected] www.eelectron.com

BO08A01KNXFI01010002.DOC

C.F. e P.IVA 11666760159
Capitale sociale: 800.000,00€ interamente versato
Tribunale di Milano 359157-8760-07
CCIAA Milano 148549

KNX PARAMETER

SETTINGS

Driver Control Telegram



1 bit



1 byte

This parameter defines whether the control of the valve is carried out with 1-bit (ON / OFF only)
or 1-byte commands (0 to 100% with intermediate positons).

Total travel time

0 ÷ 3000 sec)

This represent the total travel time necessary to move the motor reductor from totally open to
totally close.

Pause between 2 movements

100 ms ÷ 5 sec.

This represent the minimum time the motor must be in stop between 2 movements.

1 bit telegram:

Activation telegram



Telegram “0”



Telegram “1”

It is possible to set a parameter to determine if the Open movement is activated with a telegram
"0" (and then Close with "1") or vice versa.

Sending State Telegram



Disabled



When status changes



On request



Disabled

Status is never transmitted ad related communication object is
not visible



When status changes

Status is transmitted every time the relay switch changing his
status from ON to OFF or from OFF to ON.



On request

Status communication object is available and updated when
status changes but the telegram is not transmitted. Read propriety
is enabled.

Telegram Value for status sending



Telegram “0” is close



Telegram “0” is open

This set the value you want transmit when the motor reductor is in open or close position.

1 byte telegram:

Lower limit value



20%



10%



30%

Defines the minimum value below which the valve is always closed

Upper limit value



100%



80%



90%



70%

Defines the maximum value above which the valve is always open

Содержание BO08A01KNX




















































Результаты поиска

Содержание BO08A01KNX

Отзывы:

Похожие инструкции для BO08A01KNX

Бренды по названию

Популярные бренды

Eelectron BO08A01KNX, Руководство по продукту

Результаты поиска

Содержание BO08A01KNX

Отзывы:

Похожие инструкции для BO08A01KNX

Бренды по названию

Популярные бренды