manualshive.com logo in svg

Eelectron BO08A01KNX, Руководство по продукту

Поделиться
Скачать
Eelectron BO08A01KNX Скачать руководство пользователя страница 33

BO08A01KNXFI01010002.DOC 

 

 

 

Din Rail 8 Output Module– Product Handbook 

 

33/51 

Eelectron SpA, Via Magenta 77/22, I-20017 Rho (MI), Italia 
+39 02.9316681  +39 02.93507688  
[email protected]  www.eelectron.com 

BO08A01KNXFI01010002.DOC 

C.F. e P.IVA 11666760159 
Capitale sociale: 800.000,00€ interamente versato 
Tribunale di Milano 359157-8760-07 
CCIAA Milano 148549 

 

KNX PARAMETER 

SETTINGS 

Control Value 

 1 bit 

 1 byte 

This parameter defines whether the relay controls of the valve is carried out with 1-bit (ON / OFF) 
or 1-byte (0 to 100%) commands. When you select the 1-byte value the control is done through a 
PWM 

(See note 1)

. 

 

Valve Position when relay is open 

 Valve Open 

 Valve Close 

This parameter permits to set the behavior of the relay according to the state of the valve. 
If you have a valve that opens when the relay is closed and you want it to be activated by an ON 
command of a thermostat (most common situation), you must set this parameter at the value 
“Valve Closed” and the parameter (see below) “Activation telegram” with value “Telegram “0” 
close the valve” 
 

Activation telegram 

  Telegram “0” close the valve 

  Telegram “1” close the valve 

It is possible to set a parameter to determine if the function is activated with a telegram "0" (and 
then off with "1") or is activated with telegram "1" (and then off with "0"); 
 

Cycle Base Time For PWM 

5 min to 60 min in step of 5 min. 

(See note 1)

. 

 

Lower limit value 

1. 0% 
2. 10% 
3. 20% 
4. 30% 

Defines the minimum value below which the valve is always closed (0% / 10% / 20% / 30%) 
 

Upper limit value 

5. 100% 
6. 90% 
7. 80% 
8. 70% 

Defines the maximum value above which the valve is always open (70% / 80% / 90% / 100%) 
 

Sending State Telegram 

9. Disabled 
10. 

When status changes  

11. On 

request 

  Disabled  

Status is never transmitted ad related communication object is 
not visible 

 

  When status changes   

Status is transmitted every time the relay switch changing his 
status from ON to OFF or from OFF to ON.  

 

  On request 

Status communication object is available and updated when 
status changes but the telegram is not transmitted. Read propriety 
is enabled. 

 

Содержание BO08A01KNX




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды