Eelectron BO08A01KNX Скачать руководство пользователя

Страница: 36 / 51

BO08A01KNXFI01010002.DOC

Din Rail 8 Output Module– Product Handbook

36/51

Eelectron SpA, Via Magenta 77/22, I-20017 Rho (MI), Italia
+39 02.9316681 +39 02.93507688
[email protected] www.eelectron.com

BO08A01KNXFI01010002.DOC

C.F. e P.IVA 11666760159
Capitale sociale: 800.000,00€ interamente versato
Tribunale di Milano 359157-8760-07
CCIAA Milano 148549

7.3. Lock

Function

When lock function is enabled it allows, as a result of receiving a telegram on the

<Output x> Lock

Function;

to switch the relay in a defined state and force it to maintain this state even if the object

switching value changes. The behaviour of the lock function is the same described in par.

6.11

Lock

Function

This function can be enabled or with 1 bit commands than with 1 byte commands.

KNX PARAMETER

SETTINGS

Initial Value for Lock Object



Value “0”



Value “1”

This parameter selects the value of the lock object after a power on; appropriately changing this
value it is possible to start the output channel related to the lock function as “locked” or
“unlocked”. (

See note 1

Telegram for Lock Activation



Telegram “0”



Telegram “1”

This parameter selects the values associated to the “lock” or “unlock” condition.

Valve Position when Lock is Active



Valve Open



Valve Close

This parameter selects the state the valve must assume when the “lock function” becomes active”.
(

See note 2

Position when Lock Ends



Valve Open



Valve Close



Keep previous state and ignore telegrams



Keep previous state and don’t ignore

telegrams

Содержание BO08A01KNX




















































Результаты поиска

Содержание BO08A01KNX

Отзывы:

Похожие инструкции для BO08A01KNX

Бренды по названию

Популярные бренды

Eelectron BO08A01KNX, Руководство по продукту

Результаты поиска

Содержание BO08A01KNX

Отзывы:

Похожие инструкции для BO08A01KNX

Бренды по названию

Популярные бренды