manualshive.com logo in svg

Eelectron BO08A01KNX, Руководство по продукту

Поделиться
Скачать
Eelectron BO08A01KNX Скачать руководство пользователя страница 6

BO08A01KNXFI01010002.DOC 

 

 

 

Din Rail 8 Output Module– Product Handbook 

 

6/51 

Eelectron SpA, Via Magenta 77/22, I-20017 Rho (MI), Italia 
+39 02.9316681  +39 02.93507688  
[email protected]  www.eelectron.com 

BO08A01KNXFI01010002.DOC 

C.F. e P.IVA 11666760159 
Capitale sociale: 800.000,00€ interamente versato 
Tribunale di Milano 359157-8760-07 
CCIAA Milano 148549 

 

3.  General Parameter Configuration 

3.1. Parameters 

 

 

 

 
General Parameter Configuration Page list generic parameters which affects all output channels, 
or their selection applies to all contacts of the input device simultaneously regardless of the 
function selected later for each. 
 

KNX PARAMETER 

SETTINGS 

 
Delay on Power-up (3-15 sec) 
 

 
2 ÷ 15 seconds 

Through this parameter is possible to set the delay of transmission of telegrams after a power on 
by selecting the time by which the device is allowed to send telegrams. 
In large systems after a power failure or shutdown this delay avoids to generate excessive traffic 
on the bus, causing slow performance or a transmission block. 
If there are different devices that require sending telegrams on the bus after a reset, these delays 
must be programmed to prevent traffic congestion during the initialization phase. 
The input detection and the values of objects are updated accordingly at the end of the 
transmission delay time 
 
At the end of ETS programming the device behaves like after a power on. 
 

Содержание BO08A01KNX




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды