manualshive.com logo in svg

Eelectron BO08A01KNX, Руководство по продукту

Поделиться
Скачать
Eelectron BO08A01KNX Скачать руководство пользователя страница 31

BO08A01KNXFI01010002.DOC 

 

 

 

Din Rail 8 Output Module– Product Handbook 

 

31/51 

Eelectron SpA, Via Magenta 77/22, I-20017 Rho (MI), Italia 
+39 02.9316681  +39 02.93507688  
[email protected]  www.eelectron.com 

BO08A01KNXFI01010002.DOC 

C.F. e P.IVA 11666760159 
Capitale sociale: 800.000,00€ interamente versato 
Tribunale di Milano 359157-8760-07 
CCIAA Milano 148549 

 

7.  Output Configuration for Electric Valve Control 

 
 
Each of the 8 outputs can be configured to drive an electric valve (solenoid valve) typically used in 
heating and cooling systems for floor panels. 
 

 

Use this output configuration when you want to drive an ON/OFF type solenoid valve, 
without motor reductor. In this type of valve one of two states (open or closed) is 
associated with the condition of valve powered, the other to valve not powered.

 

  If you use this configuration, the control algorithm must be resident in the control device  

(thermostat, etc. ..).; the relay act only to power or not the valve.  

 
 
The functional diagram of each output configured as electric valve control is represented in the 
following scheme: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2 POINT CONTROL OBJECT :  

receive 1 bit commands  to  open and close the valve. 

CONTINUOUS CONTROL OBJECT:   receives 1 byte commands (0% -100%) to open and close 

the valve throught a PWM sequence. 

LOCK FUNCTION OBJECT:  

if enabled, according to the receipt of a 1 bit telegram, 
realizes a function for enabling / disabling the opening and  
closing of the valve 

1 BIT STATUS OBJECT:  

send information about the position (open / closed) of the 
valve using a 1 bit telegram 

1 BYTE STATUS OBJECT: 

send information about the proportion of active regulation 
using a 1 byte telegram 

 
 
 
 
 
 
 
 

RELAY 

LOCK FUNCTION 

OBJECT

 

2 POINT CONTROL 

OBJECT

 

CONTINUOUS CONTROL 

OBJECT

 

1 BIT STATUS 

OBJECT 

1 BYTE STATUS OBJECT

 

Содержание BO08A01KNX




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды