manualshive.com logo in svg

Eelectron BO08A01KNX, Руководство по продукту

Поделиться
Скачать
Eelectron BO08A01KNX Скачать руководство пользователя страница 34

BO08A01KNXFI01010002.DOC 

 

 

 

Din Rail 8 Output Module– Product Handbook 

 

34/51 

Eelectron SpA, Via Magenta 77/22, I-20017 Rho (MI), Italia 
+39 02.9316681  +39 02.93507688  
[email protected]  www.eelectron.com 

BO08A01KNXFI01010002.DOC 

C.F. e P.IVA 11666760159 
Capitale sociale: 800.000,00€ interamente versato 
Tribunale di Milano 359157-8760-07 
CCIAA Milano 148549 

Telegram Value for status sending 

  Telegram “0” when relay is open 

  Telegram “1” when relay is open 

This set the value you want transmit when relay is open or close (and therefore the valve is open 
or close according to the parameter “

Valve Position when relay is open” 

 

Anti-Locking Valve Function 

 Disabled  

 Enabled  

It is possible to enable an automatic switching valve function, useful when there are long periods 
of inactivity, for example during the summer season. If this function is activated you can select 
how long can be the period of inactivity (see parameter "

 Anti-Locking Valve Activation Period

 

"); before that the valve performs a switching ON and after 5 minutes.a switching OFF 
 

Anti-Locking Valve Activation Period 

 1 day 

 3 days 

 10 days 

Determines the maximum period of inactivity allowed. 
 

Lock Function 

 Disabled  

 Enabled 

When lock function is enabled it allows

 

switching the relay in a defined state and forcing it to 

maintain this state even if the it receives 1-bit or 1 byte control commands. 
 

Behaviour on power down 

 Valve Open 

 Valve Close 

  STOP – no movement 

When bus voltage fall down under approximately 18V device enters the power down routine and it 
is possible to set the status of the relay status (

See note 2

). 

 

Behaviour on power up 

 Valve Open 

 Valve Close 

  STOP – no movement  

On power up it is possible to set the status of each valve (and therefore the relay) with this 
parameter 

(See note 3) 

 
 

NOTES: 

 

[1]:

 

This type of control is used when you want to eliminate the hysteresis of the temperature 

typical of ON / OFF control. The relay drives the valve with ON / OFF commands and make a 
proportional control (0% ° 100%) based on the value received on the CONTINUOUS ONTROL 
OBJECT modulating the amplitudes of the On and OFF pulses (PWM). 
This mode is active when 1-byte control was previously selected. 
 

It is defined a "cycle time" in which the actuator is activated at a rate of time and then off again until 
the end of the cycle time itself. 
 

Содержание BO08A01KNX




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды